Replace coolant · ap2000p2080ga · Mercedes-Benz WIS

AP20.00-P-2080GA

Replace coolant

09.06.2016

Engine	112.945 in model 463.209/232/233/244/245/250
Engine	113.962 in model 463.206/240/241/247/248/249/254
Engine	113.982 in model 463.241/243/246
Engine	113.993 in model 463.270/271

Modification notes

26.09.2014

Mischungsverhältnis Kühlmittel

BF20.00-P-1001-04A

2	Coolant expansion reservoir

P20.00-2061-01

 Danger !	Risk of death caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
 Danger !	Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant.	Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses.	AS20.00-Z-0001-01A
	Notes on coolant		AH20.00-N-2080-01A
	Check
1	Check coolant level		AP20.00-P-2010GA
	Remove
2	Drain coolant
		ENGINE 113.993	AR20.00-P-1142GX
		ENGINE 112.945, ENGINE 113.962/982	AR20.00-P-1142HA
	Install
3	Pour in new coolant
		ENGINE 113.993	AR20.00-P-1142GX
		ENGINE 112.945, ENGINE 113.962/982	AR20.00-P-1142HA
		 A model 30 engine filled with antifreeze must not be filled later on with conventional coolant as per Sheet 325.0 or 325.2. Type 30 antifreeze may not be mixed with other antifreezes and it must be replaced every 3 years! Engine damage can occur otherwise.
		 A special antifreeze (model 30) is available for the "light alloy corrosion in cooling circuit" repair case. Indications of light alloy corrosion in the cooling circuit are:  Sludging or gel formation in cooling system  Engine overheating  Flow rate deficiency in cooler In these cases, a warning label (model 30) is to be attached in a well-visible spot on the coolant expansion reservoir (2).
		 Use antifreeze model 30 if warning label (model 30) is present on the coolant expansion reservoir (2).
		 Use only approved anti-corrosion and antifreeze agents.
		 Coolant mixing ratio	*BF20.00-P-1001-04A
		 Cooling systemCooling system	*BF20.00-P-1001-02K

 Cooling system

Number	Designation			ENGINE 112.945 in MODEL 463.209/ 232/233/244/245/ 250	ENGINE 113.962 in MODEL 463.206/ 240/241/247/248/ 249/254
BF20.00-P-1001-02K	Cooling system	Total filling capacity	Liter	11,5	12
		Filling capacity of anticorrosion agent/antifreeze down to -37 °C	Liter	5,8	6
		Filling capacity of anticorrosion agent/antifreeze down to -45 °C	Liter	6,4	6,6
		Sheet		BB00.40-P-0310-01A	BB00.40-P-0310-01A
		Sheet		BB00.40-P-0325-00A	BB00.40-P-0325-00A

 Cooling system

Number	Designation			Engine 113.982 in model 463.241/243/246	Engine 113.993 in model 463.270/271
BF20.00-P-1001-02K	Cooling system	Total filling capacity	Liter	11,9	13,0
		Filling capacity of anticorrosion agent/antifreeze down to -37 °C	Liter	5,95	6,5
		Filling capacity of anticorrosion agent/antifreeze down to -45 °C	Liter	6,55	7,3
		Sheet		BB00.40-P-0310-01A	BB00.40-P-0310-01A
		Sheet		BB00.40-P-0325-00A	BB00.40-P-0325-00A

 Coolant mixing ratio

Number	Designation				Engine all
BF20.00-P-1001-04A	Coolant mixing ratio	Antifreeze/water	Up to -37°C	%	50/50
			As of -38 °C	%	55/45
			Sheet		BB00.40-P-0310-01A
			Sheet		BB00.40-P-0325-00A
			Sheet		BB00.40-P-0326-00A

Referenced documents

ah2000n208001a Notes on coolant
ap2000p2010ga Engine cooling system - inspect fluid level, adjust to correct level. Inspect anticorrosion/ antifreeze protection, adjust to correct concentration
ar2000p1142gx Drain/pour in coolant
ar2000p1142ha
ar2000p1142ha Drain/pour in coolant
as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
as2000z000101a Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant.