Check/face-grind cylinder head contact surfaces · ar0130b7162ta · Mercedes-Benz WIS

AR01.30-B-7162TA

Check/face-grind cylinder head contact surfaces

12.02.16

Cumbustion engine 904.9 with Vehicle 693.### #S, 693.### #D, 694.### #S, 694.### #D, 958.0## #S, 958.0## #D, 979.0## #S, 979.0## #D

Cumbustion engine 906.9 with Vehicle 693.### #D, 695.### #D, 958.### #D

Check/face-grind cylinder head contact surfaces

W01.30-0019-06

1 Intake valves

2 Exhaust valve

3 Top Brake valve

4  Dial gage

5  Dial gage holder

6 Guide pin

A Guide pin projection measurement from the face of the cylinder head

B Valve recess

C Difference between the ends of the intake valve stems

H Cylinder head height

	Remove
1	Remove the cylinder head		AR01.30-B-5800TA
2	Remove the combined injector holder		AR07.03-B-6831TC
3	Remove the intake valves (1) and exhaust valves (2)		AR05.30-B-3511A
4	Remove the Top Brake valve (3)	 Only engines with Top Brake.	AR01.50-B-1000TA
	Check
5	Measure the height of the cylinder head (H)	 If necessary replace the cylinder head.	*BE01.30-B-1001-02C
6	Check the cylinder head mating surface for unevenness	 A small longitudinal deviation of the surface does not require correction, it will be compensated by the cylinder head gasket.	*BE01.30-B-1002-02C
	Machining
7	Machine the cylinder head mating surface	 Only machine the cylinder head mating surface, when  there are areas with erosion or damaged;
		 there is an inadmissible surface deviation in the longitudinal direction; and,	*BE01.30-B-1002-02C
		 the height of the cylinder head (H) still permits stock removal.	*BE01.30-B-1002-02C
		 At machining:
		 if the quality specifications of the cylinder head mating surface are not reached, leaks may occur.	*BE01.30-B-1003-02C
		 after machining, the height of the cylinder head (H) must not be below the specified measurement, otherwise damages may occur on the engine components.	*BE01.30-B-1001-02C
8	clean the cylinder head
	Measurement
9	Install the intake valves (1) and the exhaust valve (2) in the cylinder head
10	Measure and take note of the valve recess (B) in relation to the cylinder head surface and the permissible difference between the intake valves (1)		AR05.30-B-4100-01DD
		Valve recess in relation to the cylinder head face.	*BE05.30-B-1001-01D
		Difference permitted between the intake valves	*BE05.30-B-1013-01D
			*001589532100
			*363589022100
			*343589004000
		 If necessary machine the valve seats.	AR05.30-B-4511TA
	Install
11	Install the Top Brake valve (3)	 Only engines with Top Brake.	AR01.50-B-1000TA
12	Install the intake valves (1) and exhaust valve (2)		AR05.30-B-3511A
13	Assembling combinations of injector holder		AR07.03-B-6831TC
14	Install the cylinder head		AR01.30-B-5800TA

Check values for cylinder head

Número	Denominação			902.9 engine; 904.9; 906.9


BE01.30-B-1001-02C	Height of cylinder head	standard	mm	107.9...108.1
		minimum after machining	mm	106.9
BE01.30-B-1002-02C	Maximum permissible flatness deviation of cylinder head mating surface	on overall length	mm	0.05
		over a length of 150mm	mm	0.02
BE01.30-B-1003-02C	Roughness on cylinder head mating surface	Rz	mm	0.008...0.016
		R3z	mm	-

Check values for valves

Número	Denominação				Engine 904 up to final no. 415751	Engine 904 starting on final no. 415752, Engine 906


BE05.30-B-1001-01D	Distance between the valves faces and the head	Intake	Normal	mm	1.1...1.5	1.1...1.5
			Maximum repair	mm	1.7	1.7
		Exhaust	Normal	mm	1.1...1.5	1.1...1.5
			Maximum repair	mm	2.0	2.0
BE05.30-B-1013-01D	Allowable difference of the intake valve measured between the cylinder head and the valve rod end			mm	0.3	0.3

001 589 53 21 00

Measuring gage

363 589 02 21 00

Dial gage holder

343 589 00 40 00

Dial gage holder

Referenzierte Dokumente

ar0130b5800ta Zylinderkopf aus-, einbauen
ar0150b1000ta Konstantdrossel aus-, einbauen
ar0530b3511a Ventile aus-, einbauen
ar0530b410001dd Ventilrückstand zum Zylinderkopf messen
ar0703b6831tc