ar2910w0300ba

Remove/install pedal assembly

Type ar · emne 29.10 · version 0105 · 2016-08-19

Gælder for: Model 375.1 with body 375.850 Model 958.0 with body 958.860 with code XV0 (Global cockpit) Model 970, 972, 974, 975, 976 with body 972.890 except code ZX2 (EPB II)

Ikke tilgængelig på “da”; vises på Engelsk.

Placering

Funktionsgruppe 2 Chassis › 29 Pedalsystem › 29.10 Pedaler, lejebuk — Serie 375 (modeller 1**, 850) · Serie 958 (modeller 0**, 860) · Serie 970 · Serie 972 · Serie 974 · Serie 975 · Serie 976

EinPAS 37 Indvendigt udstyr › 37.50 Pedalanlæg › 37.50.40 pedalholder/pedallejebuk — Serie 375 (modeller 1**, 850) · Serie 958 (modeller 0**, 860) · Serie 970 · Serie 972 · Serie 974 · Serie 975 · Serie 976

AR29.10-W-0300BA

Remove/install pedal assembly

16.08.2016

Model

375.1 with body 375.850

Model

958.0 with body 958.860

with code XV0 (Global cockpit)

Model

970, 972, 974, 975, 976 with body 972.890

except code ZX2 (EPB II)

Remove/install pedal assembly

Shown on model 970 with code BB1 (Brake control (BS))

1

Coolant expansion reservoir

2

Electrical connector

3

Electrical connector

4

Compressed air lines

5

Pedal bracket

6

Bolts

7

Bracket

8

Compressed air line bracket

S89

Switch 2, clutch pedal

W29.10-1033-12

Remove/install pedal assembly

S85

Switch 1, clutch pedal

W25.20-1082-03

Danger !

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

Notes on compressed air connection systems

AH00.18-N-0001-01A

Remove/install

1

Switch off ignition

2

Open maintenance flap

3

Discharge compressed-air system

4

Remove trim grille

AR88.30-W-0003A

5

Pull master cylinder with attached hydraulic line out of pedal bracket (5) and tie to one side

Only for vehicles without code GE1 (Automatic gear control (AGS)).

without clutch booster

AR25.20-W-0100B

With clutch booster

AR25.20-W-0100BA

6

Disconnect electrical connections (2, 3)

Only for vehicles with code BB1 (Brake control (BS)) or with code BB8 (Brake control (BS) with ASR).

Mark installation position.

Installation: Pay attention to marking.

7

Remove all cable ties on the compressed air lines (4)

Installation: Replace cable tie.

8

Detach compressed-air lines (4)


With "VOSS 230" compressed air connector

AR42.10-W-0900A

With VOSS "232" or SCHÄFER "SDF" compressed air connector

AR42.10-W-0900C

Mark installation position of compressed air lines (4).

Installation: Check O-rings and replace if necessary. Note compressed air line (4) markings.

9

Detach compressed air line bracket (8)

10

Release coolant expansion reservoir (1) at top front plate and push to one side

If necessary, detach electrical connection from coolant level switch.

11

Remove bracket (7)

Pedal bracket to firewall

*BA29.10-N-1001-02A

12

Detach electrical connection from switch 1, clutch pedal (S85)

13

Detach electrical connection from switch 2, clutch pedal (S89)

14

Remove bolts (6) from pedal bracket (5)

Pedal bracket to firewall

*BA29.10-N-1001-02A

15

Remove pedal bracket (5) towards front

Installation: Check seal on pedal bracket (5) for damage, replace if necessary.

16

Install in the reverse order

17

Adjust brake pedal

AR29.10-W-0080A

18

Start engine and completely inflate air brake system with idle speed

19

Switch off ignition

20

Check compressed air lines (4) for leaktightness

Leak detection spray

*BR00.45-Z-1002-03A

Pedals, bearing bracket, pedal bracket

Number

Designation

Model 374.4, 375.1, 958.0, 970, 972, 974, 975, 976

BA29.10-N-1001-02A

Pedal bracket to firewall

Nm

25

Repair materials

Number

Designation

Order number

BR00.45-Z-1002-03A

Leak detection spray

Christof Fischer GmbH
www.kaeltefischer.de

Henviste dokumenter