AP35.20-D-3550A | Rear axle wheel hubs - regreasing, checking tapered roller bearings | 25.10.11 |
REAR AXLE 741.131 in MODEL 667
REAR AXLE 742.487 in MODEL 670.4
REAR AXLE 742.501 in MODEL 668, 670
D35.20-0059-06
Shown on rear axle 741.131
N35.20-2002-09
Shown on rear axle 742.501
N35.20-2003-09
Shown on rear axle 742.487
| Removing | ||
1 | Apply parking brake | ||
2 | Loosen wheel nuts on rear wheels | ||
3 | Jack up vehicle at rear axle | Place vehicle on jack stands. | |
Position jack and jack stands at the specified lift support points. | |||
4 | Remove wheels | ||
5 | Remove wheel hub | ||
Remove/install rear wheel hub | Rear axle 741.131 | ||
Rear axle 742.501 | |||
Rear axle 742.487 | |||
Puller | |||
Rear axle 742.4/5 | |||
Claw wrench | |||
Rear axle 741.131 | |||
Claw wrench | |||
6 | Clean wheel hub and tapered roller bearings | ||
| Checking | ||
7 | Check that tapered roller bearings and bearing races are in good condition and are not worn | If the tapered roller bearings are damaged they must be replaced in pairs: | |
Disassemble/assemble rear wheel hub | |||
Rear axle 741.131 | |||
Rear axle 742.501 | |||
Rear axle 742.487 | |||
| Install | ||
8 | Grease tapered roller bearings | Grease tapered roller bearings thoroughly and pack wheel hubs with the specified quantity of grease. | |
Rear axle 741.131 | |||
Capacity per wheel hub | |||
Rear axle 742.4/5 | |||
Capacity per wheel hub | |||
9 | Install wheel hub, adjust wheel bearing play | ||
Remove/install rear wheel hub | Rear axle 741.131 | ||
Rear axle 742.501 | |||
Rear axle 742.487 | |||
Rear axle 741.131 | |||
Play of wheel bearings in wheel hub | |||
Rear axle 742.4/5 | |||
Wheel bearing play | |||
Outer slotted nut, wheel hub to rear axle tube | |||
Bolt, caliper support to rear axle tube (bolt oiled) | |||
Rear axle 741.131 | |||
Collar nut, rear axle shaft to hub | |||
Rear axle 742.4/5 | |||
Bolt, rear axle shaft to wheel hub | |||
Bolt, rear axle shaft to wheel hub | |||
Dial indicator | |||
Dial indicator holder | |||
Rear axle 741.131 | |||
Claw wrench | |||
Drift | |||
Rear axle 742.4/5 | |||
Claw wrench | |||
Drift | |||
Sealant, Hylomar universal sealant 80 ml | |||
10 | Mount wheels | ||
11 | Lower rear axle | ||
12 | Tighten wheel nuts | Wheel nut | |
13 | Push down brake pedal several times |
Test values for wheel hub
Number | Designation | Rear axle 741.130/131/171, | ||
BE35.20-N-1001-02B | Play of wheel bearings in wheel hub | mm | 0.02...0.04 | |
Test and adjustment values for wheel hub
Number | Designation | Rear axle 742.4 | Rear axle 742.5 | |
BE35.20-N-1001-02A | Wheel bearing play | mm | 0.02...0.04 | 0.02...0.05 |
Hub
Number | Designation | Rear axle 741.130/131/171, | |||
BA35.20-N-1002-06C | Outer slotted nut, wheel hub to rear axle tube | Nm | 250 | ||
Hub
Number | Designation | Rear axle 742.4 | Rear axle 742.5 | |||
BA35.20-N-1002-06C | Outer slotted nut, wheel hub to rear axle tube | Nm | 250 | 250 | ||
Rear axle shaft
Number | Designation | Rear axle | |||
BA35.30-N-1003-01A | Collar nut, rear axle shaft to hub | M10 | Stage 1 | Nm | 65 |
Stage 2 | ° | - | |||
M121.5 | Nm | - | |||
Rear axle shaft
Number | Designation | Rear axle 742 | ||
BA35.30-N-1001-01B | Screw/bolt, rear axle shaft to wheel hub | M141.5 | Nm | 200 |
BA35.30-N-1003-01B | Screw/bolt, rear axle shaft to wheel hub | M121.5 | Nm | 150 |
Rear axle brake caliper
Number | Designation | Model 667 | Model 668, 670 | ||
BA42.10-N-1001-12D | Bolt, caliper support to rear axle tube (bolt oiled) | M121.5 | Nm | 110 | 110 |
M141.5 | Nm | 180 | - | ||
Wheels
Wheel hub, cap
Number | Designation | Rear axle 741.131 | ||
BF35.20-N-1001-01G | Multipurpose grease | Capacity per wheel hub | g | 100 |
Specifications for Operating Fluids | Sheet | |||
Wheel hub, cap
Number | Designation | Rear axle 742.4 | Rear axle 742.50 | ||
BF35.20-N-1001-01C | Multipurpose grease | Capacity per wheel hub | g | 100 | 100 |
Specifications for Operating Fluids | Sheet | ||||
309 589 01 07 00
Drift
Claw-type wrench
Claw-type wrench
Drift
314 589 03 07 00
312 589 14 15 00
389 589 02 15 00
035 589 01 33 00
001 589 53 21 00
363 589 02 21 00
Puller
Dial indicator holder
Dial indicator
Repair materials
Number | Designation | Order number |
BR00.45-Z-1010-01A | Sealant, Hylomar universal sealant 80 ml | A 001 989 25 20 |