Test values for distance and comparison measurement on front axle
Number | Designation | Model | Models | ||
BE40.30-P-1001-06B | Dim. | V1 | mm | 4 | 4 |
V2 | mm | 4 | 4 | ||
V3 | mm | 3 | 3 | ||
V4 | mm | - | - | ||
V5 | mm | 9923 | 10053 | ||
V6 | mm | 3 | 3 | ||
V7 | mm | 4032 | 2802 | ||
V8 | mm | 6613 | 6803 | ||
V9 | mm | 6573 | 6803 | ||
V10 | mm | - | - | ||
Fig. see | |||||
170 589 00 63 00
140 589 09 63 00
124 589 01 19 00
124 589 02 19 00
Mount
Telescopic measuring rod
Telescopic measuring rod
Set of measurement fixtures
124 589 08 63 00
Connecting pieces
P40.30-0207-01
Model 210 except model 210.08/28/6
1 Comparison measurement "V1" measured from the check bore "K" to the 6 mm hole in the transverse control arm (4), left to right.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tip (024c)
140 589 09 63 29.
If a repair bolt is installed in the right or left transverse control arm mounting, the tolerance increases to 8 mm.
This should be taken into account in the evaluation of the measuring results.
P40.30-0340-01
models 210.08/28
Comparison measurement "V1" measured from the check bore "K" to the mounting screw of the stabilizer bar on the transverse control arm (4), left to right.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tip (024f)
140 589 09 63 01
If a repair washer is installed in the right or left transverse control arm mounting, the tolerance increases to 8 mm.
This should be taken into account in the evaluation of the measuring results.
P40.30-0344-01
models 210.6
Comparison measurement "V1" measured from the check bore "K" to the contact surface of the mounting nut of the stabilizer bar on transverse control arm (4), left to right.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tip (024e)
140 589 09 63 02
If a repair washer is installed in the right or left transverse control arm mounting, the tolerance increases to 8 mm.
This should be taken into account in the evaluation of the measuring results.
P40.30-0300-01
2 Comparison measurement "V2" measured from the check bore "K" to the recess in the body longitudinal member, left to right.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tip (024d)
140 589 09 63 03.
P40.30-0301-01
3 Comparison measurement "V3" measured from the check bore "K" to the rear transverse control arm mounting, left to right. Use the center of the rubber mount on the inside of the bearing bracket as a measuring point, if necessary mark the center.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tip (024e)
140 589 09 63 02
P40.30-0214-01
4 Distance measurement "V5" of the upper suspension of the dampers at the front end. In the process bring the measuring bolt from the inside outwards (arrows) so that it just abuts the threaded spindle/damper (see cutout).
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring pin (024h)
140 589 09 63 11.
The distance measurement "V5" may only be used together with the measured camber value of the front axle for accident diagnosis, as here the position of the upper transverse control arm can only be determined indirectly.
P40.30-0306-01
5 Comparison measurement "V6" measured from the check bore " K" to the front transverse control arm mounting, left to right. Use the center of the hydro-mount on the inside of the bearing bracket as a measuring point, possibly mark the center.
Use telescopic measuring rod (06) 124 589 02 19 00 with measuring tip (024e)
140 589 09 63 02
P40.30-0303-01
6 Distance measurement "V7" measured between the front and rear transverse control arm mounting on the inside of the bearing brackets.
Use measuring rod or tape measure.
P40.30-0304-01
7 Distance measurement "V8" between the left and right rear transverse control arm mounting, measured across the center of the mounting screws. With mounting screws adjusted from the center, add 3 mm to or subtract 3 mm from the specified value depending on the adjustment direction.
Use telescopic measuring rod (06) 124 589 01 19 00 with measuring tips (024e)
140 589 09 63 02.
P40.30-0305-01
8 Comparison measurement "V9" between the left and right front transverse control arm mounting, measured across the center of the mounting screw. With mounting screws adjusted from the center, add 3 mm to or subtract 3 mm from the specified value depending on the adjustment direction.
Use telescopic measuring rod (06) 124 589 01 19 00 with measuring tips (024e)
140 589 09 63 02.
P40.30-0341-01
models 210.08/28
The mounting screws are located inside the front axle carrier.