ar3530b039502b

Determine gear backlash on countershaft gear

Tür ar · konu 35.30 · sürüm 0200 · 2017-07-12

Geçerli olduğu: Rear axle 741 in model 693.386/396 Rear axle 741.930 in model 693.348 Rear axle 741.95 in model 958.1 Rear axle 743.104 in model 386.364/367/369, 682.318 Rear axle 743.106 in model 386.364/369, 682.318 Rear axle 743.132 in model 386.354 Rear axle 743.143 in model 386.354 Rear axle 743.149 in model 386.367/369 Rear axle 743.153 in model 682.308 Rear axle 745 in model 386.059/384/387/389 Rear axle 746 in model 693.386/396

“tr” dilinde mevcut değil; İngilizce gösteriliyor.

Konumu

Fonksiyon grubu 2 Şasi › 35 Arka aks › 35.30 Tahrik, Tahrik milleri — Seri 386 (modeller 059, 354, 364, 367, 369, 384, 387, 389) · Seri 682 (modeller 308, 318) · Seri 693 (modeller 348, 386, 396) · Seri 958 (modeller 1**)

EinPAS 17 Tahrik aksamı/Aks › 17.51 Arka aks › 17.51.60 Tekerlek avara dişli demeti/dış planet dişli demeti — Seri 386 (modeller 059, 354, 364, 367, 369, 384, 387, 389) · Seri 682 (modeller 308, 318) · Seri 693 (modeller 348, 386, 396) · Seri 958 (modeller 1**)

Motorlar/şanzımanlar için de geçerli: 741 ***, 741 930, 741 95*, 743 104, 743 106, 743 132, 743 143, 743 149, 743 153, 745 ***, 746 ***

AR35.30-B-0395-02B

Determine gear backlash on countershaft gear

Rear axle

741 in model 693.386/396

Rear axle

741.930 in model 693.348

Rear axle

741.95 in model 958.1

Rear axle

743.104 in model 386.364/367/369, 682.318

Rear axle

743.106 in model 386.364/369, 682.318

Rear axle

743.132 in model 386.354

Rear axle

743.143 in model 386.354

Rear axle

743.149 in model 386.367/369

Rear axle

743.153 in model 682.308

Rear axle

745 in model 386.059/384/387/389

Rear axle

746 in model 693.386/396

Modification notes

27.06.2017

Change of figures

Work steps 1, 2 and 3

Longitudinal differential

Number

Designation

Rear axle 741.93, 741.95, 743.1, 745.5, 746.890

BE35.30-B-1001-02A

Clearance between the satellite and planetary gears teeth

mm

0,20...0,35

Compensation washers thickness

mm

3,65, 3,85, 4,00, 4,20

Determine gear backlash on countershaft gear

The clearance of the teeth flanges of the differential gearwheel in the input gearwheel depends on the thickness of the compensating washer installed between the gearwheel and the drive axle. As a starting point, a compensating washer with a thickness of 3.65 mm should be initially installed.
. 
Determine clearance between satellite gearwheel teeth and planetary gear teeth

1

Measure and note the distance "C"


The distance "C" is composed of the end of the drive shaft and the shoulder of the drive axle.


B35.30-0200-11

Determine gear backlash on countershaft gear

2

Measure and note the distance "B"


The distance "B" is composed of the end of the drive axle and the universal joint.


B35.30-0201-11

Determine gear backlash on countershaft gear

3

Calculate the measurement ("A") to determine the corresponding thickness of the compensating washer (1), as follows:
Measurement ("A") = distance ("B") - distance ("C")



4

Select the compensating washer (1) according to the measurement ("A") obtained:


Measure ("A") from 0.20 to 0.35 mm - the compensating washer (1) with thickness ("E") of 3.65 mm installed initially is correct

Measure ("A") from 0.36 to 0.50 mm - the compensating washer (1) must be replaced by one with a thickness ("E") of 3,85 mm

Measure ("A") from 0.51 to 0.70 mm - the compensating washer (1) must be replaced by one with a thickness ("E") of 4,00 mm

Measure ("A") from 0.71 to 0.90 mm - the compensating washer (1) must be replaced by one with a thickness ("E") of 4,20 mm

B35.30-0202-11