1 | Fuse box cover |
10 | Center console |
P68.20-2917-11
85 | Cover frame |
86 | Wooden cover |
87 | Screw |
S4/3 | Heater booster switch |
S46/10 | Stationary heater switch |
S97/5 | Transfer case switch |
P68.20-2829-11
8 | Screw |
11 | Screw |
P68.20-2916-04
P68.20-2757-08
5 | Heating outlet | 14 | Retaining lug | A | Cup holder | ||
6 | Cover |
6 | Cover |
7 | Socket |
9 | Telephone electrical connector |
P68.20-2918-11
| Remove/install | ||
1 | Remove fuse box cover (1) | A screw is located underneath. | |
2 | Remove screws (arrows) sideways from the center console (10) | Move seats forward or back as necessary for better accessibility of the rear screws (arrows). | |
3 | Activate service mode in Telematic Alarm Identification on Demand (emergency call system) (tele aid) | Activate/deactivate service mode in TELE AID emergency call system | |
Information on Tele Aid emergency call system | Model 463.243/244/245/250/309/322/323/332/333, 463.247/248/254/270 up to 4/1/07 | ||
Model 463.243/244/245/250/309/322/ 323/332/333 with code (ET2) tele aid – car telephone emergency call system, | |||
4 | Switch off ignition and remove ignition key | ||
Danger | Risk of explosion from explosive gas. Risk of poisoning and caustic burns from swallowing battery electrolyte. Risk of injury through burns to skin and eyes from battery acid or when handling damaged lead-acid batteries | No fires, sparks, open flames or smoking. Wear acid-resistant gloves, clothing and glasses. Only pour battery acid into suitable and appropriately marked containers. | |
5 | Disconnect battery ground line |
| |
Topical note | Notes on battery | ||
Model 463.236/248 | |||
6 | Remove cover frame (85) from shift gate | ||
7 | Remove screws (87) in the stowage compartment of the center armrest | ||
8 | Carefully remove wooden cover (86) from the center console (10) | The wooden cover (86) is only inserted in the front area. | |
9 | Detach plug from heater booster switch (S4/3), stationary heater switch (S46/10), and transfer case switch (S97/5) | ||
10 | Disconnect ambient lighting electrical connector from wooden cover (86) | Only for code (FR1) Ambient lighting | |
11 | Remove screws/bolts (8) | ||
12 | Remove cover from hand brake lever | Remove/install cover on hand brake lever | |
Mounting wedge | |||
13 | Remove cup holder (A) | Only if fitted. | |
14 | Remove rear heating outlet (5) in the center console (10) | To do this, carefully release retaining lugs (14). | |
15 | Take off cover (6) | The cover (6) is clamped on four places (top right and left, bottom right and left). | |
Mounting wedge | |||
16 | Disconnect electrical connector from socket (7) | ||
17 | Disconnect telephone electrical connector (9) | ||
18 | Remove screws (11) in the stowage compartment of the center console (10) | ||
19 | Tighten hand brake lever | ||
20 | Remove center console (10) | Lift rear center console (10). | |
21 | Install in the reverse order | ||
22 | Deactivate service mode in TELE AID emergency call system |
| |
Information on Tele Aid emergency call system | Model 463.243/244/245/250/309/322/323/332/333, 463.247/248/254/270 up to 4/1/07 | ||
23 | Read out fault memory and erase | ||
| |||
Stored faults which may be caused by assembly work, test work, removed lines or a simulation, must be processed and cleared in fault memories after completing the work. |
110 589 03 59 00
Mounting wedge