Perform wheel alignment check

AR40.20-P-0200MCC

25.9.14

MODEL	451.3/4
	without recording the vehicle level

	Measuring, adjusting
1	Check tire pressure, correct if necessary
			AP40.15-P-4061MCC
2	Perform initial measurement	 Carry out measurements according to information provided by measuring device manufacturer. Perform measurements on unladen vehicle with fuel tank 90 % full.
		Camber	*BE40.20-P-1001-06C
		Caster	*BE40.20-P-1002-06C
		Total toe at front axle	*BE40.20-P-1001-07B
		Toe-out angle with inner wheel steered through 20°	*BE40.20-P-1001-08C
		Rear axle camber	*BE40.20-P-1001-09U
		Total rear axle toe	*BE40.20-P-1001-10F
		Driveline angle	*BE40.20-P-1001-21A
3	Adjust front axle toe		AR40.20-P-0323-02MCC
		Total toe at front axle	*BE40.20-P-1001-07B
		 Jam nut at tie rod	*BA46.40-P-1002-01F
		 Open-ended socket wrench	*450589010900
4	Perform final measurement	Camber	*BE40.20-P-1001-06C
		Caster	*BE40.20-P-1002-06C
		Total toe at front axle	*BE40.20-P-1001-07B
		Toe-out angle with inner wheel steered through 20°	*BE40.20-P-1001-08C
		Rear axle camber	*BE40.20-P-1001-09U
		Total rear axle toe	*BE40.20-P-1001-10F
		Driveline angle	*BE40.20-P-1001-21A
		Should after adjusting the front axle toe other values are still outside the tolerance range or the steering wheel is not on straight:
		

		Perform advanced chassis alignment	AR40.20-P-0250MCC
5	Calibrate steering angle sensor using diagnostic system
			AD00.00-P-2000-04MCC

Inspection and setting data of front axle camber/caster

Check values for front axle toe

Number	Designation		Model 451.3/4
BE40.20-P-1001-07B	Total toe at front axle	°	+0° 36' (0° 10')

Check values for toe-out angle

Number	Designation		MODEL 451.3/4
BE40.20-P-1001-08C	Toe-out angle with inner wheel steered through 20°	°	–1° 36' ( 0° 30')

Inspection and setting data of rear axle camber

Number	Designation		MODEL 450.3/4, 451.3/4, 452.3/4
BE40.20-P-1001-09U	Rear axle camber	°	–2° 00' (0° 30')

Check values for rear axle toe

Number	Designation		MODEL 451.3/4
BE40.20-P-1001-10F	Total rear axle toe	°	+0° 00' (0° 18')

Test values for driveline angle

Number	Designation		MODEL 451.3/4
BE40.20-P-1001-21A	Driveline angle	°	+0° 0' (0° 24')

Inspection and setting data of front axle camber/caster

Number	Designation			MODEL 451.3/4
BE40.20-P-1002-06C	Caster	with 0° wheel toe		+7° 50' (0° 30')

 Tie rod

Number	Designation		MODEL 451.3/4
BA46.40-P-1002-01F	Jam nut at tie rod	Nm	50

450 589 01 09 00

Open-ended socket wrench