Remove/install electronic selector lever module (ESM)

AR27.60-P-0901GM

Remove/install electronic selector lever module (ESM)

2.5.12

 

Remove/install

1

Activate Service mode in Tele-Aid emergency call system

 Only with model 463.243/244/245/247/248/
250/254/270/309/322/323/332/333 with code ET2 Tele-Aid car phone emergency call system

AR82.95-P-0005-03GR



Notes regarding the Tele-Aid emergency call system

Model 463.243/244/245/247/248/250/

254/270/309/322/323/332/333 with code ET2 Tele-Aid car phone emergency call system

AH82.95-P-0001-01GA

 Danger!

Risk of explosion caused by escaping oxyhydrogen gas. Risk of injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte (contains diluted sulfuric acid) or metal spatter due to short circuit. Risk of burn injuries caused by short circuit. Risk of poisoning caused by swallowing battery electrolyte (contains diluted sulfuric acid) or absorption of lead over the skin or orifices

No fire, sparks, open flames or smoking.

Wear acid-resistant gloves and clothing and safety glasses with side guards.

Do not place any conductive objects on the battery and avoid any short circuit from battery positive to ground.

Only pour liquid battery electrolyte (diluted sulfuric acid) into suitable and appropriately marked containers.

AS54.10-Z-0001-01A

2

Disconnect battery ground line

 Installation: Code radio, set clock, normalize power windows and, set clock on stationary heater if installed.

Except model 463.236/248
with code (979) Special protection version

AR54.10-P-0003G

Model 463.236/248 with
code (979) Special protection version
code (ZS6) Special protection version FB6
code (ZS7) Special protection version FB7
code (E26) Additional battery 100 Ah incl. cutoff relay

AR54.10-P-0003PM



Notes on battery

All models

AH54.10-P-0001-01A

3

Unhook shift rod (8) from intermediate lever (3) from below

 Press off retainer (6) using a suitable tool.

Installation: Replace locking element (6) and bushing (7).

4

Remove center console

Model 463.202/222/236/243/244/245/

247/248/250/254/270/303/306/309/322/

323/332/333/336/340/341/346

AR68.20-P-2000GA

Model 463.237/246/249/271

AR68.20-P-2000US

5

Remove ignition switch cable (1) from the electronic selector lever module control unit (N15/5)

 Press together retaining lug (1b), press the coupling (1c) against the spring force into the electronic selector lever module control unit (N15/5), twist to the right or left though an angle of 90° (α) and detach cable of ignition lock (1).

6

Detach electrical plug (5) from electronic selector lever module control unit (N15/5)

7

Remove electronic selector lever module control unit (N15/5)

 Remove bolts (2).



*BA27.60-P-1001-02A

 Installation: Check sealing (4) is in correct installation position and inspect for signs of damage, replace if necessary.

8

Install in the reverse order

9

Set shift rod (8)

AR27.60-P-0980GM

10

Deactivate service mode in TELE AID emergency call system

 Only with model 463.243/244/245/247/248/
250/254/270/309/322/323/332/333 with code ET2 Tele-Aid car phone emergency call system

AR82.95-P-0005-03GR



Notes regarding the Tele-Aid emergency call system

Model 463.243/244/245/247/248/250/

254/270/309/322/323/332/333 with code ET2 Tele-Aid car phone emergency call system

AH82.95-P-0001-01GA

11

Connect STAR DIAGNOSIS, read out fault memory and erase if necessary

AD00.00-P-2000-04A

Number

Designation

Trans-mission 722.6

Trans-mission 722.9

BA27.60-P-1001-02A

Bolt, floor selector to body

Nm

6

6