P20.20-2472-08
1R | Right coolant feed line | 2R | Right coolant return line | 3 | Connection for coolant hose | ||
1L | Left cool coolant feed line | 2L | Left coolant return line |
4 | Heat shield |
5 | Heat shield |
6 | Heat shield |
P09.40-2474-05
Danger ! | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
Danger ! | Risk of injury caused by scraping or cutting body parts on sharp vehicle parts | Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. | |
| Remove/install | ||
1 | Drain coolant |
| |
| Notes on coolant | ||
MODEL 212, 218 with ENGINE 276.8 | |||
2 | Detach left or right air filter housing | ||
3 | Detach charge air cooler at both charge air pipes and at throttle valve actuator and pull to the front | ||
4 | Detach right or left oil line return line (2R or 2L) at connection for coolant hose (3) | ||
5 | Detach heat shield (4) or heat shield (6) | Bolt/nut for shield attachment | |
Bolt, turbocharger shield bracket to cylinder head | |||
6 | Detach bracket for rights or left coolant return line (2R or 2L) on ATL | ||
7 | Detach bracket for left coolant return line (2L) on oil filter housing and coolant thermostat | When removing the left coolant return line (2L) | |
Bolt for coolant line attachment | |||
8 | Detach right or left coolant return line (2R or 2L) on ATL and close off openings with suitable grommets | Installation: Replace sealing ring. | |
Bolt, coolant feed/return line to turbocharger | |||
Record plug | |||
9 | Detach right or left coolant return line (2R or 2L) on crankcase and close off openings with suitable grommets | Installation: Replace sealing ring. | |
Bolt, coolant feed line to crankcase | |||
Record plug | |||
10 | Remove right or left coolant return line (2R or 2L) | ||
11 | Detach heat shield (5) | ENGINE 276.8 in MODEL 207, 212, 218 | |
Bolt/nut for shield attachment | |||
12 | Detach right or left coolant feed line (1R or 1L) on ATL and close off openings with suitable grommets | Installation: Replace sealing ring. | |
Bolt, coolant feed/return line to turbocharger | |||
Record plug | |||
13.1 | Detach right or left coolant feed line (1R or 1L) on crankcase and close off openings with suitable grommets | ENGINE 276.8 in MODEL 207, 212, 218 | |
Installation: Replace sealing ring. | |||
Bolt, coolant feed line to crankcase | |||
Record plug | |||
13.2 | Detach hose for right or left coolant feed line (1R or 1L) on exhaust gas recirculation valve and close off with suitable grommets | ENGINE 276.8 in MODEL 207, 212, 218 | |
Record plug | |||
14 | Remove right or left coolant feed line (1R or 1L) | ||
15 | Install in the reverse order | ||
16 | Check engine cooling system for leaktightness |
| |
MODEL 212, 218 with ENGINE 276.8 | |||
Danger ! | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
17 | Carry out an engine test run, checking the engine for leaktightness and proper operation |
129 589 00 91 00
Record plug