Remove/install flywheel / drive plate

AR03.30-P-8001C

5.7.11

ENGINE 112.945 in MODEL 463.209 /232 /233 /244 /245 /250

ENGINE 112 in MODEL 129, 163, 170, 202, 203, 208, 209, 210, 220

ENGINE 113.962 in MODEL 463.206 /240 /241 /247 /248 /249 /254

ENGINE 113 in MODEL 129, 163, 202, 208, 209, 210, 211.076 /276, 215, 220, 230.474 /475

ENGINE 137 in MODEL 215, 220

ENGINE 112.913 in MODEL 211.061 /261

ENGINE 112.949 in MODEL 211.065 /265

ENGINE 113.967 in MODEL 211.070 /270

ENGINE 113.987 in MODEL 209.376

ENGINE 113.982 in MODEL 463.243 /246

ENGINE 112.917 in MODEL 211.080 /280

ENGINE 112.954 in MODEL 211.082 /282

ENGINE 113.969 in MODEL 211.083 /283

P03.30-0283-06

Shown on engine 112 with manual transmission

1 Flywheel with starter ring gear

2 Washer

3 Bolts

4 Cylinder pin

5 Crankshaft

6 Retaining lock

Modification notes

5.7.11

Value modified: Bolt, pressure plate to flywheel or two-mass flywheel

*BA25.10-P-1001-01A

 	Remove/install
 Danger!	Risk of death caused by vehicle slipping or toppling off the lifting platform.	Align vehicle between columns of lifting platform and position the four support plates at lifting platform support points specified by vehicle manufacturer.	AS00.00-Z-0010-01A
1.1	Remove automatic transmission	Model 129, 170, 202, 208, 210	AR27.10-P-0500B
		Model 463	AR27.10-P-0500BD
		Model 463	AR27.10-P-0500GA
		Model 230.474 /475	AR27.10-P-0500R
		Model 215, 220 without 4MATIC with engine 112, 113	AR27.10-P-0500I
		Model 220, 211 with 4MATIC with engine 112, 113	AR27.10-P-0500IW
		Model 215, 220 with engine 137	AR27.10-P-0500I
		Model 203 without 4MATIC, 209 with engine 112, 113	AR27.10-P-0500P
		Model 203 with 4MATIC	AR27.10-P-0500PW
		Model 211 without 4MATIC with engine 112, 113	AR27.10-P-0500T
		Model 163 with engine 112, 113	AR27.10-P-0500GH
1.2	Remove manual transmission	Model 210, 202, 129 with engine 112	AR26.10-P-0020A
		Model 203, 209 with engine 112	AR26.10-P-0020P
		Model 211 with engine 112	AR26.10-P-0020T
		Model 170	AR26.10-P-0020D
1.3	Remove Sequentronic automated manual transmission (AMT)	Model 203, 208, 209.3 with engine 112	AR26.10-P-0020E
		Model 211.0 with engine 112	AR26.10-P-0020TA
2	Install retaining lock (6) for crankshaft (5) and starter ring gear		AR03.30-P-5000B
3.1	Detach clutch	Vehicles with manual transmission
		 Only unscrew or screw in bolts by 1 to 1.5 turns at a time
		Model 129, 163, 170, 202, 208, 210	AR25.10-P-0050A
		Model 203, 209, 211	AR25.10-P-0050P
		 Bolt, pressure plate to flywheel or two-mass flywheel	*BA25.10-P-1001-01A
4	Remove bolts (3) of flywheel or of drive plate	 Installation: Replace bolts, because if they are used again, the connection may loosen and the bolts may shear off.
		 Torx bolts of two-mass flywheel/driven plate at crankshaft	*BA03.30-P-1002-01D
5	Remove washer (2)
6	Remove flywheel with starter ring gear (1) and drive plate	 Installation: The cylinder pin (4) determines the installation position.
	Flywheel, two-mass flywheel, drive plate, location	Engine 112, 113	GF03.30-P-8001-01B
7	Install in the reverse order
8	Carry out initialization	 If a new flywheel or drive plate is installed, perform initialization in ME control unit with STAR DIAGNOSIS in menu item "Control unit adaptation".
		STAR DIAGNOSIS diagnosis system

 Flywheel, driven plate, vibration damper, starter ring gear

Number	Designation			Engine 112


BA03.30-P-1002-01D	Bolt, two-mass flywheel/drive plate to crankshaft	Stage 1	Nm	45
		Stage 2	°	90

 Flywheel, driven plate, vibration damper, starter ring gear

Number	Designation			Engine 113.94/96/97/98	Engine 113.990/ 991/992/ 993/995	Engine 137


BA03.30-P-1002-01D	Bolt, two-mass flywheel/drive plate to crankshaft	Stage 1	Nm	45	45	45
		Stage 2	°	90	90	90

 Clutch

Number	Designation			Model 129, 140, 163, 170, 202, 203, 208, 209, 210, 211, 230	Model 461, 463


BA25.10-P-1001-01A	Bolt of pressure plate to flywheel or two-mass flywheel	Stage 1	Nm	16	16
		Stage 2	Nm	25	25

เอกสารที่อ้างถึง