ENGINE | 276.9 in MODEL 212, 218 |
P01.00-3272-08
1 | Remove air duct (2); unclip tension springs (1) to do this. |
2 | Detach ground line (3) from on-board electrical system battery (G1) and place to one side. |
Insulate connecting point for ground line (3) to avoid unintended contact of detached ground line (3) with the on-board electrical system battery (G1) ground point. |
Only perform operation steps 3 to 22 for removal of the engine.
3 | Detach cap (4) for positive battery terminal (5) from on-board electrical system battery (G1). |
4 | Detach protective cap (6a) from positive line (6). |
P01.00-3273-06
5 |
Detach positive line (6) from positive terminal clamp (7). |
6 |
Detach positive terminal clamp (7) from positive battery terminal (5) at the on-board electrical system battery (G1). |
7 |
Detach electrical connection (8) from positive terminal clamp (7). |
8 |
Detach weatherstrip (9) from suspension strut tower and center section of the bulkhead (78) and remove. |
9 |
Unclip electrical line (11) from retaining clamp (12). |
10 |
Unclip electrical line (11) from center section of the bulkhead (78). |
11 |
Unclip bracket for the electrical line (11) on center section of the bulkhead (78) and lay aside electrical line (11) on the engine. |
12 |
Detach electrical line (13) from alternator . |
13 |
Remove upper engine cover (14). |
14 |
Detach electrical connection (16a) from cylinder head cover and disconnect from connector (15). |
15 |
Detach electrical line (16) from bracket (17) for the ME-SFI [ME] control unit (N3/10). |
16 |
Disconnect electrical connections (10, 18) on ME-SFI control unit (N3/10). |
17 |
Detach retaining clamp (20) from suspension strut tower and set electrical wiring harness (19) aside. |
18 | Disconnect electrical line (22) from intelligent servo module for DIRECT SELECT (A80). |
19 | Disconnect electrical connection (24) on electric transmission oil pump (M42). |
20 | Detach ground line (23) from transmission (26). TRANSMISSION 722.9 |
21 | Detach shield (25) from transmission (26) and disconnect electrical connection on electric controller unit. TRANSMISSION 722.9 |
22 | Unclip electrical line (22) on transmission (26) and set aside. |
P01.00-3274-02
Only perform operation steps 23 to 30 for removal of cylinder head covers or rails.
23 | Remove center section of the bulkhead (78). |
24 | Disconnect electrical connections on LH intake camshaft solenoid (Y49/4) and on LH exhaust camshaft solenoid (Y49/6) or RH intake camshaft solenoid (Y49/5) and on RH exhaust camshaft solenoid (Y49/7). |
25 | Disconnect electrical connections on LH intake camshaft Hall sensor (B6/4) and on LH exhaust camshaft Hall sensor (B6/6) or RH intake camshaft Hall sensor (B6/5) and on LH exhaust camshaft Hall sensor (B6/7). |
26 | Disconnect electrical connections at the ignition coils (T1). |
P01.00-3279-12
27 | Disconnect electrical connections to fuel injectors (Y76). |
28.1 | Disconnect connector on fuel pressure and temperature sensor (B4/25). |
During removal of the left cylinder head cover or left rail. | |
When removing the right cylinder head cover or right rail. |
28.2 | Detach ground line (34) from cylinder head cover. |
29 | Detach engine wiring harness (41) on the rail. |
Installation: Ensure correct seating of the holding clip (33) on the rail. |
30 | Lay engine wiring harness (41) aside. |
P01.00-3280-12