Shown in model 292 with code 489 (AIRMATIC) except code 468 (ACTIVE CURVE SYSTEM) |
1 | Rear axle carrier |
2 | Rear axle carrier elastomer bearing |
3 | Lower wishbone control arm |
4 | Elastomer bearing on lower wishbone control arm |
5 | Rear axle differential elastomer bearing |
6 | Rear axle gear |
7 | Stabilizer bar bushing |
8 | Stabilizer bar |
9 | Tie rod elastomer bearing |
10 | Tie rod |
11 | Shock absorber elastomer bearing |
13 | Inner axle shaft boot |
26 | Rear axle shaft |
P35.20-A016-06
Shown in model 292 with code 489 (AIRMATIC) except code 468 (ACTIVE CURVE SYSTEM) |
1 | Rear axle carrier |
5 | Rear axle differential elastomer bearing |
22 | Camber strut elastomer bearing |
22a | Camber strut |
P35.20-A013-06
Shown in model 292 with code 489 (AIRMATIC) except code 468 (ACTIVE CURVE SYSTEM) |
1 | Rear axle carrier |
6 | Rear axle gear |
15 | Strut rod elastomer bearing |
15a | Strut rod |
16 | Clip |
17 | Outer axle shaft boot |
P35.20-A014-06
Shown in model 292 with code 489 (AIRMATIC) except code 468 (ACTIVE CURVE SYSTEM) |
9 | Tie rod elastomer bearing |
10 | Tie rod |
13 | Inner axle shaft boot |
16 | Clip |
19 | Coupling rod joint boots |
20 | Coupling rod joint |
21 | Level sensor linkage |
26 | Rear axle shaft |
P35.20-A015-06
Shown in model 292 with code 489 (AIRMATIC) except code 468 (ACTIVE CURVE SYSTEM) |
25 | Lower supporting ball joint boot |
P35.20-2366-06
Warning | Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities. | No parts of the body or limbs should be within the operating area of mechanical components when moving components. | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Preparatory activity | |||
1 | Release parking brake. | ||
2 | Lift vehicle with lifting platform. | ||
| |||
| Check | ||
3 | Assess the wheel bearings by firmly tugging, pushing and turning at the wheels. | If problems occur, | |
| |||
rectify the problems. | |||
After obtaining special order. | |||
4 | Check rear axle carrier (1) for cracks, deformation and corrosion. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
5 | Check rear axle carrier elastomer bearings (2) for cracks, deformation and wear, and check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
6 | Check lower wishbone control arm (3) for cracks, deformation and corrosion. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
7 | Check lower wishbone control arm elastomer bearings (4) for cracks, deformation and wear, and check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
8 | Check rear axle differential elastomer bearings (5) for cracks, deformation and wear, and check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
9 | Check rear axle differential (6) for cracks, deformation, leaktightness and corrosion. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
10 | Check stabilizer bushings (7) for cracks, deformation and wear, and check for play by firmly pulling and pushing on stabilizer bar (8). | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
11 | Check stabilizer bar (8) for correct seating, cracks, deformation, corrosion and play. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
12 | Check tie rod elastomer bearings (9) for cracks, deformation and wear, and check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
13 | Check tie rods (10) for correct seating, cracks, deformation, corrosion and play. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
14 | Check shock absorber elastomer bearings (11) for cracks, deformation and wear, then check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
15 | Check strut rod elastomer bearings (15) for cracks, deformation and wear, and check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
16 | Check strut rods (15a) for correct seating, cracks, deformation, corrosion and play. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
17 | Check outer drive shaft boots (17) for condition, leaktightness and correct seating. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
18 | Check clamps (16) of outer drive shaft boots (17) for cracks, deformation, corrosion and correct seating. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
19 | Check inner drive shaft boots (13) for condition, leak tightness and correct seating. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
20 | Check clamps (16) of inner drive shaft boots (13) for cracks, deformation, corrosion and correct seating. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
21 | Check rear axle shafts (26) for cracks, deformation and corrosion, and check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
22 | Check camber strut rod elastomer bearings (22) for cracks, deformation and wear, and check for play by firmly pulling and pushing. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
23 | Check camber struts (22a) for correct seating, cracks, deformation, corrosion and play. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
24 | Check coupling rod joint boots (19) for proper condition, leaktightness and correct seating. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
25 | Check coupling rod joints (20) for play by firmly pulling and pushing. | If problems occur, | |
| |||
rectify the problems. | |||
After obtaining special order. | |||
26 | Check level sensor linkages (21) for correct seating, cracks, deformation, corrosion and play. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
27 | Check lower supporting joint boots (25) of lower wishbone control arms (3) for condition, leaktightness and correct seating. | If necessary, use commercially available devices/tools. | |
If problems occur, | |||
| |||
rectify the problems. | |||
After obtaining special order. | |||
28 | Check lower supporting joints for play by pulling and pushing firmly on the lower wishbone control arms (3). | If problems occur, | |
| |||
rectify the problems. | |||
After obtaining special order. | |||
Finishing activity | |||
29 | Lower vehicle with vehicle lift. | ||
|