Remove/install gasoline particulate filter temperature sensor

AR49.20-P-0200MRM

Remove/install gasoline particulate filter temperature sensor

27.03.2020

Model

167 with engine 264, 274.9

with code 598 (Gasoline particulate filter (OPF) with sensor system)

Shown on model 167 with engine 274.9

1

Connector

3

Jack

B163/4

Temperature sensor upstream of gasoline particulate filter

2

Bracket

4

Electrical line

 Warning

Risk of burn injuries, suffocation and poisoning when working on the exhaust system and the components connected to it. Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust. Risk of poisoning caused by skin contact with solid components of the exhaust.

Wear protective clothing and safety glasses. Use the extraction system. Move people out of the hazard area.

AS49.00-Z-0001-01A

 Caution

Risk of injury caused by scraping or cutting body parts on sharp vehicle parts

Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.

AS00.00-Z-0017-01A

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

Topical note

Notes on avoiding damage through contamination and foreign objects

AH00.00-P-5000-01A

 

Remove/install

1

Remove center engine compartment lining and rear engine compartment lining.

AR61.20-P-1105ME

 Installation: Only install center engine compartment lining and rear engine compartment lining after leak test.

2

Remove cover under transfer case.

AR61.30-P-1001ME

 Installation: Only install cover after leak test.

3

Unclip connector (1) with jack (3) from bracket (2).

4

Release connector (1) and disconnect from jack (3).

5

Remove electric line (4) from brackets (arrows) at transmission and expose up to temperature sensor upstream of gasoline particulate filter (B163/4).

6

Remove temperature sensor upstream of gasoline particulate filter (B163/4).

Note on calculation of tightening torque when using insertion or socket tools with various effective lengths

AH00.00-P-0015-01CW

 Installation: Coat thread of temperature sensor upstream of gasoline particulate filter (B163/4) with heat-resistant lubricating paste.

 Model 167 with engine 274.9
with code 598 (Gasoline particulate filter (OPF) with sensor system)Temperature sensor to gasoline particulate filter

*BA07.04-P-1007-01N

 Model 167 with engine 264
with code 598 (Gasoline particulate filter (OPF) with sensor system)Temperature sensor to gasoline particulate filter

*BA07.04-P-1002-02B

Paste, hot lubrication 1 kg, DBL 6879.20

*BR00.45-Z-1005-06A

 Box wrench bit

*000589690300

7

Seal threaded hole in gasoline particulate filter with a suitable stop plug.

 Record plug

*129589009100

8

Install in the reverse order.

9

Read out and delete fault memory.

If temperature sensor upstream of gasoline particulate filter (B163/4) was replaced.



AD00.00-P-2000-06ME

 Warning

Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running.

Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

10

Perform an engine test run; check engine for proper operation and check exhaust system for leak tightness.

11

Install cover under transfer case.

AR61.30-P-1001ME

12

Install center engine compartment lining and rear engine compartment lining.

AR61.20-P-1105ME

 Sensors

Number

Designation

Engine 264

BA07.04-P-1002-02B

Temperature sensor to gasoline particulate filter

Nm

45

 Sensors, transmitters

Number

Designation

Engine 274

BA07.04-P-1007-01N

Temperature sensor to gasoline particulate filter

Nm

45

Repair materials

Number

Designation

Order number

BR00.45-Z-1005-06A

Paste, hot lubrication 1 kg, DBL 6879.20

A 000 989 76 51