P32.20-2169-09
Shown on model 251 with all-round level control system, code 489
1 Stabilizer bar
2 Bolts
3 Bolts
4 Retaining clamps for stabilizer bar
5 Retaining clamps for torsion bushing
6 Nuts
7 Link rods
8 Nuts
Modification notes
19.10.11 | Value hanged: screw/bolt, retaining clamp for stabilizer bar to front axle carrier | ||
Value changed: Nut, link rod to front damper | |||
Value changed: Nut, link rod to stabilizer bar | |||
Value changed: Nut, link rod to stabilizer bar |
| Removing | ||
Danger! | Risk of injury caused by pinching or crushing when working on springs or spring bodies that are under tension | Use only approved tensioning devices; shield off hazard area if necessary. | |
Danger! | Risk of injury caused by moving parts that can pinch, crush or, in extreme cases, even sever extremities | No parts of the body or limbs should be within the operating range of the mechanism when moving components. | |
Danger! | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | |
| Notes on self-locking nuts and bolts | All models | |
| When working on the front-end assembly, be careful not to scratch, mark or notch the surfaces of aluminum parts. Otherwise the service life of the parts will be affected | ||
1 | Raise vehicle using drive-on lifting platform | ||
2.1 | Detach lower engine compartment paneling | Vehicles with gasoline engine. | |
2.2 | Remove bottom section of soundproofing | Vehicles with diesel engine. | |
3.1 | Unscrew nuts (8) of link rods (7) and detach link rods (7) from stabilizer bar (1) | Only if link rods (7) are obviously undamaged. | |
3.2 | Unscrew nuts (6) of link rods (7) and detach link rods (7) from front shock absorbers | Only if link rods (7) are obviously defective. | |
4 | Remove bolts (2) of stabilizer bar retaining clamps (4) and detach both stabilizer bar retaining clamps (4) | Detach the stabilizer bar retaining clamps (4) carefully as the stabilizer bar (1) is under tension. | |
Mark installation positions. | |||
5 | Remove stabilizer bar (1) from front axle carrier | ||
6 | Remove bolts (3) of torsion bushing retaining clamps (5) and detach torsion bushings from stabilizer bar (1) | Only if a new stabilizer bar (1) or new torsion bushings are being installed. | |
Mark installation positions. | |||
7 | Detach link rods (7) from stabilizer bar (1) | Only if the link rods (7) have not been detached from the stabilizer bar (1). | |
| Checking | ||
8 | Check link rods (7) and torsion bushings for damage | Replace if necessary. | |
| Install | ||
Installation | Only tighten nuts and bolts of chassis components when vehicle is in a ready-to-drive condition. | ||
9 | Attach link rods (7) to stabilizer bar (1) | Only if new link rods (7) are being installed. | |
Do not tighten the nuts (8) yet. | |||
10 | Attach torsion bushings to stabilizer bar (1) and preassemble bolts (3) with appropriate nuts to torsion bushing retaining clamps (5) | Only if a new stabilizer bar (1) or new torsion bushings are being installed. | |
Transfer the previously made markings to the new stabilizer bar (1). Align the torsion bushing retaining clamps (5) with the markings. Do not tighten nuts of bolts (3) yet. | |||
11 | Position stabilizer bar (1) on front axle, install stabilizer bar retaining clamps (4) and insert bolts (2) | Observe previous markings. Align stabilizer bar (1) in center. The bent ends of the stabilizer bar (1) must point downward. Do not tighten bolts (2) yet. | |
12.1 | Mount link rods (7) onto front shock absorbers and screw on nuts (6) | Only if new link rods (7) have been fitted. | |
Do not tighten the nuts (6) yet. | |||
12.2 | Mount link rods (7) onto stabilizer bar (1) and screw on nuts (8) | Only if the link rods (7) were not previously removed. | |
Do not tighten the nuts (8) yet. | |||
13 | Make sure that stabilizer bar (1), torsion bushing retaining clamps (5) and stabilizer bar retaining clamps (4) are positioned correctly | Realign if necessary. | |
14 | Fully tighten bolts (3) | | |
15 | Fully tighten bolts (2) | | |
16 | Tighten nuts (6) | Only if new link rods (7) have been fitted. | |
| |||
17 | Tighten nuts (8) | | |
18.1 | Install lower engine compartment paneling. | Vehicles with gasoline engine. | |
18.2 | Install bottom part of soundproofing | Vehicles with diesel engine. | |
19 | Lower vehicle using drive-on lifting platform |
Front axle stabilizer bar
Number | Designation | Model | ||
BA32.20-P-1001-02L | Bolt, stabilizer bar retaining clamp to bearing bracket | Nm | 180 | |
BA32.20-P-1002-02L | Bolt, torsion bushing retaining clamp | Nm | 40 | |
BA32.20-P-1003-02L | Nut, link rod to front shock | Stage 1 | Nm | 100 |
2nd stage loosen | ° | 180 | ||
Stage 3 | Nm | 120 | ||
Stage 4 | ° | 45 | ||
BA32.20-P-1004-02L | Nut, link rod to stabilizer bar | Stage 1 | Nm | 100 |
2nd stage loosen | ° | 180 | ||
Stage 3 | Nm | 120 | ||
Stage 4 | ° | 45 | ||
Documente menționate
- ah0000n000101a Indicaţii pentru şuruburile şi piuliţele autoblocante
- ar6120p1105rt
- ar9430p5300rt
- as0000z000101a Pericol de rănire prin prindere sau strivire în cazul lucrărilor efectuate la arcuri sau elemente de arc pretensionate
- as0000z000901a Pericol de rănire prin prinderea sau strivirea, în caz extrem prin tăierea membrelor în timpul manipulării sistemului mecanic
- as0000z001001a Pericol de moarte prin alunecare sau basculare a autovehiculului de pe elevator