1 | Cable duct |
2 | Bolts |
T1/1 | Cylinder 1 ignition coil |
T1/2 | Cylinder 2 ignition coil |
T1/3 | Cylinder 3 ignition coil |
T1/4 | Cylinder 4 ignition coil |
P15.12-A031-05
Warning | Risk of injury. Skin or eye injuries may result when handling hot or glowing objects. | Wear protective gloves, protective clothing and safety glasses, if necessary. | |
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
Topical note | Notes on avoiding damage to ignition system | ||
| Remove/install | ||
1 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
2 | Remove upper engine cover. | ||
| |||
3 | Remove cable duct (1) and place to one side. | Screw, engine cable duct to cylinder head cover/charge-air distributor/oil separator/high-pressure pump shielding | |
4 | Release and disconnect electrical connectors of the ignition coils (T1/1, T1/2, T1/3, T1/4). | ||
5 | Remove screws (2). | Screw/bolt, ignition coil to cylinder head cover | |
6 | Detach ignition coils (T1/1, T1/2, T1/3, T1/4) with spark plug connectors upward and remove. | Installation: | |
Installation: Approx. Fill 1 g of spark plug connector grease into the spark plug connector. | |||
Spark plug connector grease | |||
7 | Check ignition coils (T1/1, T1/2, T1/3, T1/4) and spark plug connectors for damage. | If there is a problem, | |
| |||
Replace corresponding components. | |||
8 | Install in the reverse order. | ||
| Check | ||
9 | Connect vehicle diagnosis system, read out fault memory and clear if necessary. | ||
| |||
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
10 | Conduct engine test run while checking for proper operation of the engine. |
Documente menționate
- ad0000p200006me
- ah0000p500001a Indicaţii pentru evitarea defecţiunilor din cauza impurităţilor şi corpurilor străine
- ah1510p000201v Indicaţii pentru evitarea producerii de avarii la instalaţia de aprindere
- ah5400p000101a Indicaţii pentru evitarea defectării componentelor electronice prin descărcare electrostatică
- ap0110p240501o Demontare, montare capace motor
- as0000z000201a Pericol de rănire la piele şi ochi prin manipulare cu obiecte fierbinţi sau incandescente
- as0000z000501a Pericol de accident prin pornirea de pe loc cu motorul aflat în funcţionare. Pericol de rănire prin striviri şi arsuri la manipularea în timpul pornirii motorului sau cu motorul aflat în funcţionare
- as0000z003501a Pericol de moarte în cadrul lucrărilor la componentele şi sistemele cu U >= 30 V tensiune alternativă (CA) respectiv cu U >= 60 V tensiune continuă (CC)