ar3531p052003h

Check rear axle differential oil level, correct if necessary

Tipo ar · tema 35.31 · versão 0207 · 2007-05-02

Válido para: Rear axle center assembly dia. 240 in MODEL 240

Não disponível em “pt”; apresentado em Inglês.

Onde se situa

Grupo funcional 2 Chassí › 35 Eixo traseiro › 35.31 Parte central do eixo traseiro — Série 240

EinPAS 17 Trem de força/eixo › 17.51 Eixo traseiro › 17.51.65 diferencial do eixo traseiro/diferencial longitudinal — Série 240

AR35.31-P-0520-03H

Check rear axle differential oil level, correct if necessary

Oil filler/drain screw on rear axle differential modified

Phased in 19.01.04

BT35.31-P-0015-01A

Modification notes

20.3.04

The oil filler screw should always be replaced after being unscrewed from the rear axle center assembly.

The new oil filler screw as well as the tapped hole must be cleaned with a special cleaning spray and the oil filler screw provided with a special sealing compound

Only carry out oil level check at interior temperature.

Rear axle center assembly housing

Number

Designation

Model 240

BA35.31-P-1002-02A

Oil filler screw, rear axle differential

Nm

50

Rear axle differential

Number

Designation

Model
215.374/376/379,

Model
220.074/174/
176/179/875/
876,

Model
240

BF35.31-P-1001-01M

Filling capacity

Rear axle differential Ø 240 mm
in rear axle differential 240V

Liters

1.9

Rear axle differential Ø 240 mm
in rear axle differential 240FE

Liters

1.6

Specifications for Operating Fluids

Sheet

BB00.40-P-0235-07A

Repair materials

Number

Designation

Order number

BR00.45-Z-1061-01A

Sealant, Omnifit 100H (50 g)

A 002 989 23 71

BR00.45-Z-1046-04A

Cleaning spray, Loctite 7063 (150ml)

A 001 986 71 71 10

Check rear axle differential oil level, correct if necessary

P35.31-2007-02

Only carry out the oil level check at interior temperature and not on a rear axle center assembly which is at operating temperature. Oil which is otherwise needed might flow out when the rear axle center assembly is hot.

1 Clean area around oil filler screw (50 g).

2 Remove oil filler screw (50 g)

3 If necessary collect which runs out and allow to run out until the oil only drips out of the opening.

4 Check oil level.

The rear axle is correctly filled when the oil reaches the bottom edge of the oil filler hole. If necessary refill with hypoid gear oil.

The fully synthetic oil can also be used without reservation for rear axle gears manufactured before 04.11.2001. Mixing old Universal hypoid gear oil and the new FE hypoid gear oil does not lead to any impairment of the basic functions such as wear characteristics, leaktightness etc. on the rear axle gear, but should nevertheless be avoided on account of the better fuel economy.

Shown on rear axle differential dia. 198 mm

50g Oil filler plug

50h Oil drain screw

Check rear axle differential oil level, correct if necessary

P35.31-2158-01

Replace oil filler screw (50g).

5 Coat Loctite 7063 cleaning spray on a rag and clean the new oil filler screw (50g) and tapped hole in the rear axle center assembly.
The oil filler screw (50g) and tapped hole must be free from oil and grease.

6 Apply about one droplet of Omnifit 100H sealing compound on the second or third lower thread.

7 Screw in and tighten oil filler screw (50g) in the rear axle center assembly and tighten .

Documentos referenciados