D72.16-1384-07
Shown on right sliding door (2) |
1 | Door lock | 2 | Sliding door | 4 | Cables | ||
1.1 | Cable | 3 | Bolts | 6 | Bearing bracket |
D72.16-1385-09
Shown on right sliding door (2) |
1 | Door lock | 7 | Sliding door control unit | 11 | Bolts | ||
1.1 | Cable | 8 | Bracket | 12 | Upper rotary tumbler actuator motor | ||
1.2 | Cable drive | 9 | Electrical connector | ||||
2 | Sliding door | 10 | Bolts |
Warning | Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. | No parts of the body or limbs should be within the operating area when the components are moving. | |
Topical note | Notes on carrying out repair work in the vehicle interior | ||
| Remove/install | ||
1 | Remove lower door trim of left and/or right sliding door (2). | Model 907.6/7 with code VA1 (Load compartment trim up to belt rail standard) or with code V4A (Right load compartment sliding door full trim), model 907.6 with code VA2 (Load compartment interior trim up to roof height (wood)) or with code VA3 (Load compartment interior trim up to roof height, can be washed) | |
Model 907.6/7 with code VA1 (Load compartment interior trim up to belt rail standard), model 907.6 with code VA2 (Load compartment interior trim up to roof height (wood)) or with code VA3 (Load compartment interior trim up to roof height, can be washed) | |||
Model 907.6/7 with code V4A (Right load compartment sliding door full trim) | |||
2 | Remove upper rotary tumbler. | Model 907.6/7 with code D03 (Roof and rear-end doors, high version), model 907.6 with code D05 (Super-high roof) or with code D06 (Super-high roof painted in vehicle color) | |
3 | Remove screw/bolts (3). | Bolt, door lock to sliding door | |
4 | Get into load compartment or passenger compartment and manually close sliding door (2) until door lock (1) is accessible. | Door lock (1) must not be locked. | |
5 | Remove door lock (1) from sliding door (2) until cables (4) at door lock (1) can be accessed. | ||
6 | Remove cables (4) from door lock (1). | ||
7 | Remove cable (1.1) from bearing bracket (6). | ||
8 | Remove cable (1.1) from inner door panel of sliding door (2). | Installation: Replace damaged fasteners. | |
9 | Unclip sliding door control unit (7) from bracket (8) and place to one side with connected electric lines. | ||
10 | Detach electrical connection (9). | ||
11 | Unscrew bolts (10). | ||
12 | Turn bracket (8) around until screws (11) can be accessed. | ||
13 | Remove screws (11) and remove upper rotary tumbler actuator motor (12) from bracket (8) and place to one side with connected electrical wiring harness. | ||
14 | Disconnect electrical connector at door lock (1) and remove door lock (1) together with cable drive (1.2) installed at bracket (8) from sliding door (2). | ||
15 | Remove bracket (8) from cable drive (1.2). | If door lock (1) is replaced. | |
16 | Install in the reverse order. | ||
| Check | ||
17 | Perform function test of door lock (1). |
Powiązane dokumenty
- ah6800n000101s Wskazówki dotyczące wykonywania prac naprawczych we wnętrzu pojazdu
- ar7216d4034ts
- ar7216d6612ts
- ar7216d6612tsb
- as0000z001101a Niebezpieczeństwo zranienia przez zakleszczenie lub zmiażdżenie palców podczas demontażu, montażu i prac regulacyjnych przy pokrywach, drzwiach i oknie dachowym.