Remove/install sliding door trim pieces

AR72.16-D-6612TSB

Remove/install sliding door trim pieces

06.03.2020

Model

907.6/7

with code V4A (Fully lined right load compartment sliding door)

Modification notes

26.07.2018

Method and operation step sequence changed.

Shown on model 907.6 with code T55 (electrical actuation for right sliding door)

15

Unlocking

Shown on model 907.7 with code EL9 (2-way speaker system, front and rear)

1

Lower door trim

2

Retaining clips (12 pcs.)

3

Sliding door

Shown on model 907.7 with code D05 (super-high roof)

3

Sliding door

5

Retaining clips (8 pcs)

7

Adhesive tape strips

4

Upper door trim

6

Adhesive tape strips

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 

Remove/install

1

Enter the load compartment or passenger compartment and close the sliding door (3).

 Model 907.6/7
with code T55 (Electric operation of sliding door on right)
with code V4A (Fully lined right load compartment sliding door)
Installation: Completely open and close sliding door (3) twice with corresponding push button switch.
Keep the push button switch pressed throughout the entire normalization run.
For normalization of the electric drive of the sliding door (3).

2

Set release (15) to "MAN" position using a suitable screwdriver.

Model 907.6/7
with code T55 (Electric operation of sliding door on right)
with code V4A (Fully lined right load compartment sliding door)

 This deactivates the electric drive of the sliding door (3).

3.1

Disassemble bottom door trim (1) at retaining clips (2) from sliding door (3) and remove.

Model 907.6/7
with code V4A (Fully lined right load compartment sliding door)
except code EL9 (Two-way loudspeaker system in front and rear)

 Installation: Replace damaged retaining clips (2).

 Clip remover

*452589016300

3.2

Remove bottom door trim (1) at retaining clips (5) from the sliding door (4), disconnect electrical connectors from the speakers, and remove bottom door trim (1).

Model 907.6/7
with code EL9 (Two-way loudspeaker system in front and rear)
with code V4A (Fully lined right load compartment sliding door)

 Installation: Replace damaged retaining clips (5).

 Clip remover

*452589016300

4

Unclip retaining clips (5) of upper door trim (4) at sliding door (3), release upper door trim (4) from tape strips (6, 7) and remove.

Model 907.6/7
with code D03 (Roof and rear-end doors, high version)
with code V4A (Fully lined right load compartment sliding door)
Model 907.6
with code D05 (Super-high roof)
with code V4A (Fully lined right load compartment sliding door)
Model 907.6
with code D06 (Super-high roof painted in vehicle colour)
with code V4A (Fully lined right load compartment sliding door)

 Installation: Clean bonding surfaces on the sliding door (3).
Replace damaged retaining clips (5).

Assembly cleaner

*BR00.45-Z-1028-04A

 Clip remover

*452589016300

5

Clean bonding surfaces at sliding door (3).

 Installation:
Bonding surfaces must be completely clean.
Adhesion of tape strips (6, 7) is otherwise not ensured.

Assembly cleaner

*BR00.45-Z-1028-04A

6

Replace tape strips (6).

Model 907.6/7
with code D03 (Roof and rear-end doors, high version)
with code V4A (Fully lined right load compartment sliding door)
Model 907.6
with code D05 (Super-high roof)
with code V4A (Fully lined right load compartment sliding door)
Model 907.6
with code D06 (Super-high roof painted in vehicle colour)
with code V4A (Fully lined right load compartment sliding door)
If upper door trim (4) is not replaced.

 Installation:
Bonding surfaces must be completely clean before new tape strips (6) are affixed.
Adhesion of tape strips (6) is otherwise not ensured.

3M 5745 Acrylic Foam adhesive tape

*BR00.45-Z-1194-02A

Assembly cleaner

*BR00.45-Z-1028-04A

7

Replace tape strips (7).

Model 907.6/7
with code D03 (Roof and rear-end doors, high version)
with code V4A (Fully lined right load compartment sliding door)
Model 907.6
with code D05 (Super-high roof)
with code V4A (Fully lined right load compartment sliding door)
Model 907.6
with code D06 (Super-high roof painted in vehicle colour)
with code V4A (Fully lined right load compartment sliding door)
If upper door trim (4) is not replaced.

 Installation:
Bonding surfaces must be completely clean before new tape strips (7) are affixed.
Adhesion of tape strips (7) is otherwise not ensured.

Adhesive tape SKS 100 PE foam 4 mm

*BR00.45-Z-1193-02A

Assembly cleaner

*BR00.45-Z-1028-04A

8

Install in the reverse order.

Repair materials

Number

Designation

Order number

BR00.45-Z-1028-04A

Assembly cleaner

A 000 986 56 01

BR00.45-Z-1193-02A

Adhesive tape SKS 100 PE foam 4 mm

SKS GmbH
https://www.sks-gmbh.com

BR00.45-Z-1194-02A

3M 5745 Acrylic Foam adhesive tape

SKS GmbH
https://www.sks-gmbh.com