Remove/install sliding door trim pieces

AR72.16-D-6612TS

Remove/install sliding door trim pieces

18.06.2018

Model

907.6/7

except code V4A (Fully lined right load compartment sliding door)

Model

910.6

Modification notes

04.06.2018

Normalization of electric sliding door added.

Operation step 7

Shown on model 907.6 with code T55 (electrical actuation for right sliding door)

15

Release

Shown on right sliding door (4) on model 907.6 with code D05 (super-high roof) and with code VA2 (load compartment interior trim to roof height (wood))

1

Lower trim panel

2

Center trim

3

Upper trim panel

4

Sliding door

5

Retaining clips (12x)

6

Retaining clips (10x)

7

Retaining clips (8x)

 Warning

Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.

No parts of the body or limbs should be within the operating area when the components are moving.

AS00.00-Z-0011-01A

Topical note

Notes on carrying out repair work in the vehicle interior

AH68.00-N-0001-01S

 

Remove/install

1

Enter the load compartment or passenger compartment and close left and/or right sliding door (4).

2

Set release (15) on sliding door (4) to "MAN" position using a suitable screwdriver.

Model 907.6/7
with code T55 (Electric operation of sliding door on right)
except code V4A (Fully lined right load compartment sliding door)
Model 907.6/7
with code T56 (Electric operation of sliding door on left)
except code V4A (Fully lined right load compartment sliding door)

 This deactivates the electric drive of the sliding door (4).

3.1

Disassemble bottom door trim (1) at retaining clips (5) from sliding door (4) and remove.

Model 907.6/7
except code EL9 (Two-way loudspeaker system in front and rear)
except code V4A (Fully lined right load compartment sliding door)
Model 910.6

 Installation: Replace damaged retaining clips (5).

 Clip remover

*452589016300

3.2

Remove bottom door trim (1) at retaining clips (5) from the sliding door (4), disconnect electrical connectors from the speakers, and remove bottom door trim (1).

Model 907.6/7
with code EL9 (Two-way loudspeaker system in front and rear)
except code V4A (Fully lined right load compartment sliding door)

 Installation: Replace damaged retaining clips (5).

 Clip remover

*452589016300

4

Disassemble center door trim (2) at the retaining clips (6) from the sliding door (4) and remove.

 Installation: Replace damaged retaining clips (6).

 Clip remover

*452589016300

5

Disassemble top door trim (3) at the retaining clips (7) from the sliding door (4) and remove.

Model 907.6/7
with code D03 (Roof and rear-end doors, high version)
except code V4A (Fully lined right load compartment sliding door)
Model 907.6
with code D05 (Super-high roof)
except code V4A (Fully lined right load compartment sliding door)
Model 907.6
with code D06 (Super-high roof painted in vehicle colour)
except code V4A (Fully lined right load compartment sliding door)
Model 910.6
with code D03 (Roof and rear-end doors, high version)

 Installation: Replace damaged retaining clip (7).

 Clip remover

*452589016300

6

Install in the reverse order.

7

Completely open and close sliding door (4) twice with corresponding push button switch.

Model 907.6/7
with code T55 (Electric operation of sliding door on right)
except code V4A (Fully lined right load compartment sliding door)
Model 907.6/7
with code T56 (Electric operation of sliding door on left)
except code V4A (Fully lined right load compartment sliding door)

 For normalization of electric drive of sliding door (4).
Keep push button switch pressed throughout normalization run.



Check

8

Perform speaker function test in the bottom door trim (1).

Model 907.6/7
with code EL9 (Two-way loudspeaker system in front and rear)
except code V4A (Fully lined right load compartment sliding door)