Remove/install lower hinge of front passenger door · ar7210p0004mfa · Mercedes-Benz WIS

AR72.10-P-0004MFA

Remove/install lower hinge of front passenger door

05.11.2019

Model

118, 177, 247

Remove/install lower hinge of front passenger door

P72.12-3221-09

Shown on model 177.0

1.1	Hinge leaf	3	Nuts
1.2	Hinge support	4	Damping material
2	Screw

 Warning	Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	No parts of the body or limbs should be within the operating area when the components are moving.	AS00.00-Z-0011-01A
Topical note	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
	Notes on safety-relevant components		AH00.00-Z-0019-01A
	Remove
1	Remove front door sill.		AR68.30-P-4101MFA
2	Mark the installation position for the hinge wing (1.1) and hinge support (1.2).	 The bottom hinge consists of the hinge wing (1.1) and hinge support (1.2).
3	Support front passenger door with suitable means and fix in place.	 The front passenger door must be supported and fixed in place. Otherwise, the front passenger door will be damaged.
4	Remove nuts (3).	 If necessary, push the damping (4) to the side.
5	Unscrew screw (2) and remove hinge leaf (1.1) with hinge support (1.2).
	Install
6	Clean contact surfaces in area of hinge supports.	Cleaner	*BR00.45-Z-1025-04A
7	Align hinge support (1.1) using the markings made previously and tighten the screw (2) slightly by hand.
8	Align hinge support (1.2) using the markings made previously and tighten nuts (3) slightly by hand.	 Helper required.
9	Close and open front passenger door.	 The installation position of the passenger door may change later due to opening and closing.
	Check
10	Check gap dimensions at front passenger door.	Model 118	AR60.00-P-0700-01MFC
		Model 177, 247	AR60.00-P-0700-01MFA
		Model 118Front door to fender	*BE60.00-P-1009-01NA
		Model 118Front door to rear door	*BE60.00-P-1010-01NA
		Model 118Longitudinal member panel to front door/rear door	*BE60.00-P-1024-01NA
		Model 177Front door to rear door	*BE60.00-P-1009-01JA
		Model 177Front door to fender	*BE60.00-P-1008-01JA
		Model 177Longitudinal member panel to fender/front door/rear door	*BE60.00-P-1025-01JA
		Model 177Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01JA
		Model 247Front door to rear door	*BE60.00-P-1009-01MA
		Model 247Front door to fender	*BE60.00-P-1008-01MA
		Model 247Longitudinal member panel to front door/rear door	*BE60.00-P-1025-01MA
		Model 247Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01MA
		 Feeler gauge	*129589032100
		If there are problems,
		
		Adjust gap dimensions of front passenger door.
		Model 118	AR72.10-P-0550MFC
		Model 177, 247	AR72.10-P-0550MFA
11	Tighten the screw (2) and nuts (3).	 Nut, hinge to body	*BA72.10-P-1002-01ZA
		 Screw/bolt, hinge to front door	*BA72.10-P-1001-01ZA
12	Repair paint damage at corresponding bolt heads.		AR98.00-P-0150CW
13	Protect the front passenger door and A-pillar against corrosion in area of hinge leaf (1.1) and hinge support (1.2).		AR97.20-P-1500MFA
14	Install front door sill.		AR68.30-P-4101MFA

Test and adjustment values for gap dimensions

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1008-01JA	Front door to fender	Dimension "H"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.0	Model 247.6
BE60.00-P-1008-01MA	Front door to fender	Dimension "H"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.7
BE60.00-P-1008-01MA	Front door to fender	Dimension "H"	mm	4(+0,5/-1)
		For picture, see		AR60.00-P-0700-01MFA

Test and adjustment values for gap dimensions

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1009-01JA	Front door to rear door	Dimension "I"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.0	Model 247.6
BE60.00-P-1009-01MA	Front door to rear door	Dimension "I"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.7
BE60.00-P-1009-01MA	Front door to rear door	Dimension "I"	mm	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1009-01NA	Front door to fender	Dimension "G"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

Test and adjustment values for gap dimensions

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1010-01JA	Front door cover to rear door cover (B-pillar)	Dimension "J"	mm	4 (1)	4 (1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.0	Model 247.6
BE60.00-P-1010-01MA	Front door cover to rear door cover (B-pillar)	Dimension "J"	mm	4 (1)	4 (1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.7
BE60.00-P-1010-01MA	Front door cover to rear door cover (B-pillar)	Dimension "J"	mm	4 (1)
		For picture, see		AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1010-01NA	Front door to rear door	Dimension "H"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

Gap dimensions

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1024-01NA	Longitudinal member panel to front door/rear door	Dimension "V"	mm	5 (1)	5 (1)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

Test and adjustment values for gap dimensions

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1025-01JA	Longitudinal member panel to fender/front door/rear door	Dimension "Y"	mm	5 (1)	5 (1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.0	Model 247.6
BE60.00-P-1025-01MA	Longitudinal member panel to front door/rear door	Dimension "Y"	mm	5,0 (1)	-
		For picture, see		AR60.00-P-0700-01MFA	-

Gap dimensions

Number	Designation			Model 247.7
BE60.00-P-1025-01MA	Longitudinal member panel to front door/rear door	Dimension "Y"	mm	-
		For picture, see		-

 Front door

Number	Designation			Model 118	Model 177, 247
BA72.10-P-1001-01ZA	Screw/bolt, hinge to front door	Initial tightening torque (hold period 2 s)	Nm	-	50
		Subsequent tightening	Nm	40	40

 Front door

Number	Designation		Model 118	Model 177, 247
BA72.10-P-1002-01ZA	Nut, hinge to body	Nm	40	40

129 589 03 21 00

Feeler gauge

Repair materials

Number	Designation	Order number
BR00.45-Z-1025-04A	Cleaner	A 005 989 19 71

Powiązane dokumenty

ah0000n000101a Wskazówki dotyczące samozabezpieczających śrub i nakrętek
ah0000z001901a Wskazówki dotyczące elementów wpływających na bezpieczeństwo
ar6000p070001mfa
ar6000p070001mfc
ar6830p4101mfa
ar7210p0550mfa
ar7210p0550mfc
ar9720p1500mfa
ar9800p0150cw Zestawienie przeglądowe środków MB i ich stosowania
as0000z001101a Niebezpieczeństwo zranienia przez zakleszczenie lub zmiażdżenie palców podczas demontażu, montażu i prac regulacyjnych przy pokrywach, drzwiach i oknie dachowym.