Adjust front door · ar7210p0550mfa · Mercedes-Benz WIS

AR72.10-P-0550MFA

Adjust front door

05.11.2019

Model

177, 247

P72.10-4985-09

Shown on model 177.0

1	Front door	5	Hinge
2	Bolts	6	Screw
3	Lock striker	7	Hinge
4	Screw

Shown on model 177.0

8	Nuts
9	Nuts
10	Screw

P72.10-4986-06

 Warning	Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	No parts of the body or limbs should be within the operating area when the components are moving.	AS00.00-Z-0011-01A
 Warning	Risk of injury. Moving parts can pinch, crush or, in extreme cases even sever extremities.	No parts of the body or limbs should be within the operating area of mechanical components when moving components.	AS00.00-Z-0009-01A
	Notes on safety-relevant components		AH00.00-Z-0019-01A
	Remove
1	Switch off ignition and store transmitter key outside of transmitter range (min. 2 m).
2	Remove bolts (2) and remove lock striker (3)
3	Remove screw (10) and move door holder to zero position.	 Move door holder to zero position. The paint will be damaged otherwise.
	Check
4	Check adjustment of front door (1).		AR60.00-P-0700-01MFA
		 The contour of the front fender should be flush with the contour of the front door (1) or may protrude by a maximum of 1 mm.
		Model 247Longitudinal member panel to front door/rear door	*BE60.00-P-1025-01MA
		Model 247Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01MA
		Model 247Front door to rear door	*BE60.00-P-1009-01MA
		Model 247Front door to fender	*BE60.00-P-1008-01MA
		Model 177Longitudinal member panel to fender/front door/rear door	*BE60.00-P-1025-01JA
		Model 177Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01JA
		Model 177Front door to rear door	*BE60.00-P-1009-01JA
		Model 177Front door to fender	*BE60.00-P-1008-01JA
		 Feeler gauge	*129589032100
	Adjust
5	Release screw (4) at hinge (5), adjust front door (1) and retighten screw (4).		AR60.00-P-0700-01MFA
		 Do not loosen screw (4) and screw (6) at the same time. Otherwise, paint damage will occur if the front door (1) makes contact with other component parts.
		 The hinges (5, 7) must not be placed under stress during adjustment. The hinges (5, 7) will otherwise be damaged.
		Model 247Longitudinal member panel to front door/rear door	*BE60.00-P-1025-01MA
		Model 247Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01MA
		Model 247Front door to rear door	*BE60.00-P-1009-01MA
		Model 247Front door to fender	*BE60.00-P-1008-01MA
		 Screw/bolt, hinge to front door	*BA72.10-P-1001-01ZA
		Model 177Longitudinal member panel to fender/front door/rear door	*BE60.00-P-1025-01JA
		Model 177Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01JA
		Model 177Front door to rear door	*BE60.00-P-1009-01JA
		Model 177Front door to fender	*BE60.00-P-1008-01JA
		 Feeler gauge	*129589032100
6	Release screw (6) at hinge (7), adjust front door (1) and retighten screw (6).		AR60.00-P-0700-01MFA
		 Do not loosen screw (6) and screw (4) at the same time. Otherwise, paint damage will occur if the front door (1) makes contact with other component parts.
		 The hinges (5, 7) must not be placed under stress during adjustment. The hinges (5, 7) will otherwise be damaged.
		Model 247Longitudinal member panel to front door/rear door	*BE60.00-P-1025-01MA
		Model 247Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01MA
		Model 247Front door to rear door	*BE60.00-P-1009-01MA
		Model 247Front door to fender	*BE60.00-P-1008-01MA
		 Screw/bolt, hinge to front door	*BA72.10-P-1001-01ZA
		Model 177Longitudinal member panel to fender/front door/rear door	*BE60.00-P-1025-01JA
		Model 177Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01JA
		Model 177Front door to rear door	*BE60.00-P-1009-01JA
		Model 177Front door to fender	*BE60.00-P-1008-01JA
		 Feeler gauge	*129589032100
		If adjustment via screws (4, 6) at hinges (5, 7) is insufficient,
		
		Continue with operation steps (7 to 10).
	Remove
7	Remove door sill.	If making adjustments via the screws (4, 6) is not sufficient.
			AR68.30-P-4101MFA
8	Only release nuts (8) at A-pillar to extent that front door (1) can be adjusted; adjust front door (1), retighten nuts (8).	If making adjustments via the screws (4, 6) is not sufficient.
			AR60.00-P-0700-01MFA
		 The hinges (5, 7) must not be placed under stress during adjustment. The hinges (5, 7) will otherwise be damaged.
		 Only loosen the nuts (8) as far as necessary. Otherwise, paint damage will occur if the front door (1) makes contact with other component parts.
		Model 247Longitudinal member panel to front door/rear door	*BE60.00-P-1025-01MA
		Model 247Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01MA
		Model 247Front door to rear door	*BE60.00-P-1009-01MA
		Model 247Front door to fender	*BE60.00-P-1008-01MA
		 Nut, hinge to body	*BA72.10-P-1002-01ZA
		Model 177Longitudinal member panel to fender/front door/rear door	*BE60.00-P-1025-01JA
		Model 177Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01JA
		Model 177Front door to rear door	*BE60.00-P-1009-01JA
		Model 177Front door to fender	*BE60.00-P-1008-01JA
		 Feeler gauge	*129589032100
9	Remove instrument panel.	If making adjustments via the screws (4, 6) is not sufficient.
			AR68.10-P-1000MFA
10	Expose nuts (9) at A-pillar.	If making adjustments via the screws (4, 6) is not sufficient.
11	Loosen nuts (9) only so far that the front door (1) can be adjusted; adjust the front door (1) and tighten nuts (9) again.	If making adjustments via the screws (4, 6) is not sufficient.
			AR60.00-P-0700-01MFA
		 Only loosen the nuts (9) as far as necessary. Otherwise, paint damage will occur if the front door (1) makes contact with other component parts.
		 The hinges (5, 7) must not be placed under stress during adjustment. The hinges (5, 7) will otherwise be damaged.
		Model 247Longitudinal member panel to front door/rear door	*BE60.00-P-1025-01MA
		Model 247Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01MA
		Model 247Front door to rear door	*BE60.00-P-1009-01MA
		Model 247Front door to fender	*BE60.00-P-1008-01MA
		 Nut, hinge to body	*BA72.10-P-1002-01ZA
		Model 177Longitudinal member panel to fender/front door/rear door	*BE60.00-P-1025-01JA
		Model 177Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01JA
		Model 177Front door to rear door	*BE60.00-P-1009-01JA
		Model 177Front door to fender	*BE60.00-P-1008-01JA
		 Feeler gauge	*129589032100
	Adjust
12	Position lock striker (3) on B-pillar and screw in screws (2) up to stop.	 It must still be possible to adjust the lock striker (3).
13	Align lock striker (3) by carefully closing front door (1).	 The contour of the front door (1) should be flush with the contour of the rear door or may protrude by a maximum of 1 mm.
14	Tighten screws (2).	 Screw, front door lock striker to body	*BA72.10-P-1008-01ZA
	Install
15	Repair paint damage on screw heads of screws (4, 6).
Topical note	General notes on touch-up applicators and paint spray cans		AH98.00-P-9409-06A
16	Protect front door (1) and A-pillar in area of the two hinges (5, 7) against corrosion.
Topical note	Notes on cavity preservation		AH97.20-P-0001-01B
		Wax for engine compartment (400 ml spray can)	*BR00.45-Z-1018-05A
17	Install instrument panel.	When the instrument panel is removed.
			AR68.10-P-1000MFA
18	Install door sill.	When the door sill is removed.
			AR68.30-P-4101MFA
19	Tighten screw (10).	 Bolt, door holder on body	*BA72.10-P-1006-01ZA
	Concluding tasks
20	Calibrate 360° camera for left outside mirror (B84/7) or 360° camera for right outside mirror (B84/8) by performing a calibration drive.	Model 177, 247 with code 501 (360° camera)
			AD00.00-P-2000-06MFA

Test and adjustment values for gap dimensions

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1008-01JA	Front door to fender	Dimension "H"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.0	Model 247.6
BE60.00-P-1008-01MA	Front door to fender	Dimension "H"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.7
BE60.00-P-1008-01MA	Front door to fender	Dimension "H"	mm	4(+0,5/-1)
		For picture, see		AR60.00-P-0700-01MFA

Test and adjustment values for gap dimensions

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1009-01JA	Front door to rear door	Dimension "I"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.0	Model 247.6
BE60.00-P-1009-01MA	Front door to rear door	Dimension "I"	mm	4 (0,5)	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.7
BE60.00-P-1009-01MA	Front door to rear door	Dimension "I"	mm	4 (0,5)
		For picture, see		AR60.00-P-0700-01MFA

Test and adjustment values for gap dimensions

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1010-01JA	Front door cover to rear door cover (B-pillar)	Dimension "J"	mm	4 (1)	4 (1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.0	Model 247.6
BE60.00-P-1010-01MA	Front door cover to rear door cover (B-pillar)	Dimension "J"	mm	4 (1)	4 (1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.7
BE60.00-P-1010-01MA	Front door cover to rear door cover (B-pillar)	Dimension "J"	mm	4 (1)
		For picture, see		AR60.00-P-0700-01MFA

Test and adjustment values for gap dimensions

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1025-01JA	Longitudinal member panel to fender/front door/rear door	Dimension "Y"	mm	5 (1)	5 (1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

Gap dimensions

Number	Designation			Model 247.0	Model 247.6
BE60.00-P-1025-01MA	Longitudinal member panel to front door/rear door	Dimension "Y"	mm	5,0 (1)	-
		For picture, see		AR60.00-P-0700-01MFA	-

Gap dimensions

Number	Designation			Model 247.7
BE60.00-P-1025-01MA	Longitudinal member panel to front door/rear door	Dimension "Y"	mm	-
		For picture, see		-

 Front door

Number	Designation			Model 177, 247
BA72.10-P-1001-01ZA	Screw/bolt, hinge to front door	Initial tightening torque (hold period 2 s)	Nm	50
		Subsequent tightening	Nm	40

 Front door

Number	Designation		Model 177, 247
BA72.10-P-1002-01ZA	Nut, hinge to body	Nm	40

 Front door

Number	Designation		Model 177, 247
BA72.10-P-1006-01ZA	Bolt, door holder on body	Nm	25

 Front door

Number	Designation		Model 177, 247
BA72.10-P-1008-01ZA	Screw, front door lock striker to body	Nm	24

129 589 03 21 00

Feeler gauge

Repair materials

Number	Designation	Order number
BR00.45-Z-1018-05A	Wax for engine compartment (400 ml spray can)	A 000 986 33 70 10

Powiązane dokumenty

ad0000p200006mfa
ah0000z001901a Wskazówki dotyczące elementów wpływających na bezpieczeństwo
ah9720p000101b Wskazówki dotyczące konserwacji profili zamkniętych
ah9800p940906a Ogólne wskazówki dotyczące lakierów w sztyfcie i w aerozolu
ar6000p070001mfa
ar6810p1000mfa
ar6830p4101mfa
as0000z000901a Niebezpieczeństwo zakleszczenia lub zmiażdżenia, w skrajnym przypadku obcięcia kończyn podczas prac przy układach mechanicznych.
as0000z001101a Niebezpieczeństwo zranienia przez zakleszczenie lub zmiażdżenie palców podczas demontażu, montażu i prac regulacyjnych przy pokrywach, drzwiach i oknie dachowym.