Remove/install propeller shaft

AR41.10-D-0050TS

Remove/install propeller shaft

19.06.2019

Model

907

1

Propeller shaft

2

Propeller shaft intermediate bearing

3

Propeller shaft intermediate bearing (for 3-piece propeller shaft (1))

1

Propeller shaft

4

Flex disk (model 907 except code ZG1 (Engageable all-wheel drive) and except code ZG3 (Engageable all-wheel drive with transmission ratio))

5

Screws (model 907 except code ZG1 (Engageable all-wheel drive) and except code ZG3 (Engageable all-wheel drive with transmission ratio))

6

Bolts

 Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Topical note

Notes on threaded connections fastened using a tightening angle-based tightening process

AH00.00-P-0020-01A

Topical note

Notes on self-locking nuts and bolts

AH00.00-N-0001-01A

Topical note

Notes on installing propeller shaft

AH41.10-N-0001-01TS

 

Remove/install

1

Raise vehicle.

AR00.60-D-1000-04TS

Topical note

Special instructions for lifting and supporting vehicle

AH00.60-N-0100-01TS

2

Remove underbody paneling.

Model 907
with code XM1 (Noise reduction)

AR61.30-D-1001TS

3

Remove check straps.

AR41.10-D-0050-01TS

 The number of check straps varies depending on the wheelbase.

 Bolt, check strap to frame

*BA41.10-N-1004-01TS

4

Remove front propeller shaft intermediate bearing (2) from vehicle floor.

 Helper required.

 Model 907
with code ZG1 (Engageable all-wheel drive)
Model 907
with code ZG3 (Engageable all-wheel drive with gear reduction)
Installation: Check for correct positioning of spacer disks.

 Bolt, propeller shaft intermediate bearing to frame

*BA41.40-N-1001-02TS

5

Remove rear propeller shaft intermediate bearing (3) from vehicle floor.

If a 3-piece propeller shaft (1) is installed.

 Two helpers required.

 Model 907
with code ZG1 (Engageable all-wheel drive)
Model 907
with code ZG3 (Engageable all-wheel drive with gear reduction)
Installation: Check for correct positioning of spacer disks.

 Bolt, propeller shaft intermediate bearing to frame

*BA41.40-N-1001-02TS

6.1

Counterhold propeller shaft (1), remove screws (5) and remove propeller shaft (1) with flex disk (4) from output flange of transmission.

Model 907
except code ZG1 (Engageable all-wheel drive)
except code ZG3 (Engageable all-wheel drive with gear reduction)
If flex disk (4) is installed.

 Helper required.
If a 3-piece propeller shaft is installed, the aid of two helpers is required.

 Installation: Check flex disk (4) for wear and damage.

 Screw, flex disk to transmission output flange

*BA41.10-N-1003-01TS

If corresponding findings are present,



Replace flex disk (4).

AR41.10-D-0040TS

6.2

Counterhold propeller shaft (1), remove screws and remove propeller shaft (1) from output flange of transmission.

Model 907
except code ZG1 (Engageable all-wheel drive)
except code ZG3 (Engageable all-wheel drive with gear reduction)
If flex disk (4) is not installed.

 Helper required.

 Screw, propeller shaft to output flange of transmission/transfer case

*BA41.10-N-1001-01TS

6.3

Counterhold propeller shaft (1), remove screws and remove propeller shaft (1) from output flange of transfer case.

Model 907
with code ZG1 (Engageable all-wheel drive)
Model 907
with code ZG3 (Engageable all-wheel drive with gear reduction)

 Helper required.

 Screw, propeller shaft to output flange of transmission/transfer case

*BA41.10-N-1001-01TS

7

Counterhold propeller shaft (1), remove screws (6) from drive flange of rear axle differential and remove propeller shaft (1).

 Helper required.
If a 3-piece propeller shaft is installed, the aid of two helpers is required.

 Screw, propeller shaft to rear axle differential drive flange

*BA41.10-N-1002-01TS

8

Install in the reverse order

 Propeller shaft

Number

Designation

Model 907 except code G42

Model 907 with code G42

BA41.10-N-1001-01TS

Screw, propeller shaft to output flange of transmission/transfer case

M10x1

Stage 1

Nm

40

-

Stage 2

°

60

-

M12x1.5

Stage 1

Nm

40

66

Stage 2

°

60

55

 Propeller shaft

Number

Designation

Model 907 except code G42

Model 907 with code G42

BA41.10-N-1002-01TS

Screw, propeller shaft to rear axle differential drive flange

M10x1

Stage 1

Nm

40

40

Stage 2

°

60

60

 Propeller shaft

Number

Designation

Model 907 with code G42

BA41.10-N-1003-01TS

Screw, flex disk to transmission output flange

M10x1

Stage 1

Nm

-

Stage 2

°

-

M12x1.5

Stage 1

Nm

66

Stage 2

°

55

 Propeller shaft

Number

Designation

Model 907 except code G42

Model 907 with code G42

BA41.10-N-1004-01TS

Bolt, check strap to frame

Nm

70

70

 Propeller shaft intermediate bearing

Number

Designation

Model 907

BA41.40-N-1001-02TS

Bolt, propeller shaft intermediate bearing to frame

M12x1.5

Nm

135