W26.40-1003-09
1 | Flange central bolt | 12 | Intermediate shaft | |
2 | Stop washer | 13 | Device: Supporting plate | |
3 | Output flange | 14 | Fixing bolt | |
4 | Radial seal | 15 | Gearbox rear part | |
5 | Pulse spider | 16 | Pulse sender unit | |
6 | Internal hexagonal screws | 17 | Reverse gear axle | |
7 | End cover | 18 | Spacer ring | |
8 | Toroidal gasket | 19 | Gasket | |
9 | Control guide | 20 | Intermediary shaft cover | |
10 | Annular gasket | 21 | Cover screws | |
11 | Secondary shaft | 22 | Control guide screws |
| Remove | ||
1 | Remove the front part of the transmission |
| |
Transmission with clutch hydraulic central drive. | |||
2 | Place the rear of the transmission (15) with the two axles on the supporting plate (13) | Mounting plate | |
Retaining spring | |||
3 | Remove the output flange (3) | Retainer wrench | |
4 | Remove the radial sealant (4) and the pulse spider (5) | ||
5 | Remove the pulse sender unit (16) | ||
6 | Remove the retaining screws (14) | ||
7 | Remove the hinged cover (7) | ||
8 | Remove the control guide (9) | Release the locking screws on the control guide (22). | |
9 | Remove the cover (20) | ||
10 | Remove spacer ring (18) | ||
11 | Remove the reverse gear shaft (17) | Insertion and extraction tool | |
Impact extractor | |||
Threaded insert | |||
12 | Remove the rear part of the transmission (15) |
| |
| Install | ||
13 | Install the rear part of the transmission (15) |
| |
Insertion and extraction tool | |||
Sleeve | |||
14 | Install the reverse gear (17) | The reverse gear and the bearing with the needle roller must be in their exact position. Lubricate the reverse gear shaft (17), insert 2/3 of the shaft manually and continue until the stop tapping with a plastic hammer. | |
Install the thread so that it points towards the cover (20). | |||
Anticorrosion grease 40 g / DB supply specification 6834.00 | |||
15 | Install the pulse spider (5) and the radial sealant (4) | Replace the radial sealant (4). | |
Drift | |||
16 | Rest the power output flange (3) | Replace the central bolt (1). | |
.Central power outlet flange on primary shaft screw | |||
Retainer wrench | |||
17 | Check the accommodation of the controls | Disassembling and assembling shift detent | |
The drive parts should move smoothly, if necessary: | |||
| |||
18 | Rest the control guide (9) and the hinged cover (7) | The operating rods must be in neutral position. | |
Installation: Replace the round section seal rings (10) and (8). | |||
.Rear cover of the axle | |||
19 | Secure the screws (22) on the control guide lock | In case of greater resistance, move the operating rods together forwards and backwards. | |
Lever blockage mechanism fastening bolts to control guide | |||
20 | Install the pulse sender unit (16) | .Speed sensor in the gearbox cover | |
21 | Install the retaining screws (14) | Safety screws to the housing of the transmission rear part | |
22 | Assemble the supporting plate (13) on the transmission power take-off flange |
| |
Mounting plate | |||
23 | Rotate the rear of the transmission (15) downwards along with the power output flange | ||
24 | Install the front part of the gearbox |
| |
Transmission with clutch hydraulic central drive. | |||
25 | Install the spacer ring (18) | ||
26 | Place the cover (20) on the rear part of the transmission case | Install a new gasket (19). | |
.Cover on the rear part of the gearbox (close to the transmission shaft) |
715 589 02 14 00
Sleeve
715 589 00 43 00
Insertion and extraction tool
715 589 02 63 00
Retaining spring
715 589 01 63 00
Mounting plate
383 589 02 63 00
Threaded insert
355 589 01 63 00
Impact extractor
717 589 00 31 00
Retainer wrench
715 589 06 15 00
Drift