1 Cap
2 Expansion reservoir
3 Coolant hose
4 Clamp
5 Radiator
P20.00-2346-03
Modification notes
Drain | |||
Danger! | Risk of injury to skin and eyes caused by scalding from contact with hot coolant spray. Risk of poisoning caused by swallowing coolant. | Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses. | |
| Notes on coolant | ||
1 | Remove maintenance flap | ||
2 | Turn cooling system cap (1) on engine radiator (2) a half turn counterclockwise, relieve the pressure and then unscrew the cooling system cap (1) | ||
Danger! | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | |
3 | Raise vehicle using the vehicle lift and remove underfloor paneling | Cordless drill/driver, cordless drill | |
4 | Loosen clamp (4) of coolant hose (3), detach coolant hose (3) from radiator (5) and drain coolant | Catch coolant in a suitable vessel. | |
Filling | |||
5 | Position coolant hose (3) on radiator (5) and fasten with clamp (4) | Replace hose clamp (4). | |
6 | Lower vehicle with vehicle lift | ||
7 | Pour in coolant and bleed cooling system | ||
| |||
| |||
| Coolant specifications | Sheet 310.1 | |
| Anticorrosion/antifreeze agents (Sheet 325.0) | Sheet 325.0 | |
8 | Seal expansion reservoir (2) with cap (1) | ||
| Checking | ||
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. | |
9 | Run engine until warm | Until the coolant fan motor cuts in. | |
10 | Turn cooling system cap (1) on engine radiator (2) a half turn counterclockwise, relieve the pressure and then unscrew the cooling system cap (1) | ||
11 | Check coolant level in the expansion reservoir (2) and correct if necessary | The engine coolant level in the coolant expansion reservoir (2) must be positioned at the max. marking. | |
| Coolant specifications | Sheet 310.1 | |
| Anticorrosion/antifreeze agents (Sheet 325.0) | Sheet 325.0 | |
12 | Seal expansion reservoir (2) with cap (1) | ||
13 | Raise vehicle with vehicle lift | ||
14 | Install underfloor paneling | ||
15 | Lower vehicle with vehicle lift | ||
16 | Install maintenance flap |
450 589 20 63 00
Filling device
Pressure pump
450 589 07 21 00
Powiązane dokumenty
- ah2000n208001a Wskazówki dotyczące płynu chłodzącego
- ar2000p114206mcd
- as0000z000501a Niebezpieczeństwo wypadku na skutek samoczynnego ruszenia przy pracującym silniku. Niebezpieczeństwo obrażeń na skutek zmiażdżenia lub poparzenia przy wykonywaniu czynności podczas rozruchu lub przy pracującym silniku.
- as0000z001001a Zagrożenie życia na skutek ześlizgnięcia lub spadnięcia pojazdu z podnośnika.
- as2000z000101a Niebezpieczeństwo zranienia skóry i oczu przez poparzenie wytryskującym, gorącympłynem chłodzącym. Niebezpieczeństwo zatrucia na skutek połknięcia płynu chłodzącego
- bb0040p031001a Przepisy dotyczące płynów chłodzących
- bb0040p032500a Środki zapobiegające korozji i zamarzaniu (specyfikacja 325.0)