Release and position rear drive module

AR01.00-P-3050SR

Release and position rear drive module

30.4.15

Engine

281 in model 453

Shown on engine 281.920 with transmission 700.12

1

Rear muffler

4

Bracket

9

Vacuum line

2

Elastomer bearing

7

Hydraulic line (with transmission 700.12)

10

Screw

3

Ground cable

8

Bracket

11

Positive line

Shown on engine 281.910

5

Coolant hoses

14

Air intake hose

22

Engine mount

6

Bracket

15

Electrical line

Y58

Fuel tank vent valve

12

Fuel line

16

Nut

13

Cable tie

17

Engine mount

Shown on engine 281.920

18

Flange

20

Piston

19

Nut

21

Knurled knob

 Danger !

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

Lower, position

1

Remove covering over engine

2

Secure vehicle on vehicle lift

AR00.60-P-0100SR

3

Remove underfloor paneling

4

Remove rear axle crossmember

AR35.15-P-0250SR

5

Remove control arm

AR35.15-P-0204SR

6

Remove front engine mount on transmission housing, unfasten of the body side and swivel downwards

AR22.10-P-4330SR

7

Unhook rear muffler (1) from the right elastomer bearing (2)

8

Remove bracket (4) with ground line (3)

9

Unclip coolant hoses (5) from bracket (6)

10

Unclip hydraulic line (7) for clutch operation from bracket (8) and unfasten from the body

Engine 281 in model 453 with transmission 700.12

11

Unclip vacuum lines (9) from the brackets on the body

12

Remove screw/bolt (10) and detach positive line (11) from the body

13

Unclip fuel line (12) from the brackets on the body

14

Remove cable tie (13) from engine wiring harness

15

Remove air intake hose (14)

16.1

Remove shift cables from transmission

Engine 281 in model 453 with transmission 700.12

AR26.60-P-6626SR

16.2

Remove cable for selector lever lock from transmission

Engine 281 in model 453 with transmission 700.41

AR27.60-P-0002SR

17

Unhook fuel tank bleed valve (Y58) at the body

18

Unclip electrical line (15) for fuel tank bleed valve (Y58) on air filter housing

19

Unfasten nuts (16) for engine mount (17, 22)


Do not unscrew nuts (16) for engine mount (17, 22) completely.
The engine may fall down otherwise.

 Nut, engine mount to bearing pin

*BA22.10-P-1004-01H

20

Attach engine support fixture

AR01.10-P-2400-06SR



000 588 03 62 00 Lifting platform

WS01.00-P-0091A

 Adaptation

*453589016200

21

Remove engine mounts (17)

AR22.10-P-1101SR

22

Remove engine mounts (22)

AR22.10-P-1102SR

23

Place flange (18) for drainage pin on the threaded pins of the engine mount flange and tighten nuts (19) finger-tight

 Lowering bolts

*453589006200

24

Screw piston (20) of the drainage pin onto the engine support bearing pin

25

Tighten piston (20) of the drainage pin at the knurled knob (21) finger-tight

26

Raise vehicle with the vehicle lift in stages until the piston (20) of the drainage pin has moved completely into the flange (18) and the engine hangs free


When lifting onto hose, watch out for lines and detachable parts.
They can be damaged otherwise.

 Helper required.

27

Remove engine support fixture

AR01.10-P-2400-06SR



000 588 03 62 00 Lifting platform

WS01.00-P-0091A

 Adaptation

*453589016200

28

Position in reverse order

 Engine mounts, engine supports

Number

Designation

Engine 281 in model 453

BA22.10-P-1004-01H

Nut, engine mount to bearing pin

Nm

62