P88.20-0326-09
2 Lining
3 Fog lamp connector
6 Spreading rivet
7 Rotary clip
4 Screw
5 Outside temperature sensor
P88.20-0332-06
1 Bumper
8 Screw
9 Telescoping nozzle for headlamp cleaning system
10 Telescoping nozzle cover
11 Screw
12 Nut
P88.20-0337-09
13 Guide
14 Holder
15 Centering pin
18 Fender tip
C Gap dimension from headlamp lens to bumper cover
16 Holder
17 Intermediate layer
| Removal | ||
1 | Remove paneling (2) | ||
2 | Disconnect fog lamp connector (3) | ||
3 | Unscrew screw (4) | ||
4 | Disconnect outside temperature sensor (5) | ||
5 | Remove spreading rivet (6) from wheelhouse panel | ||
6 | Open rotary clip (7) on side of fender flange | ||
7 | Unscrew screws (8) | ||
8 | Remove cover (9) on telescoping nozzle (10) | With SAA 500.305/01 Headlamp cleaning system Have second mechanic press headlamp cleaning system switch momentarily until telescoping nozzle (10) extends. Pull telescoping nozzle (10), release headlamp cleaning system switch, remove cover (9) and release telescoping nozzle (10). | |
9 | Unscrew screw (11) | ||
10.1 | Transfer AMG bumper | See installation instructions for accessories | |
Retrofit AMG paneling parts, model 208.3 coupe | |||
Retrofit AMG paneling parts, model 208.4 convertible | |||
11 | Unscrew nuts (12) and remove bumper (1) | ||
| Installation | ||
12 | Position bumper (1) on body and slide guide (13) onto holder (14) while inserting centering pin (15) into holder (16) | ||
13 | Press bumper (1) up in area of wheelhouse and fasten with rotary clip (7) | ||
14 | Start nuts (12) loosely on studs | ||
15 | Align bumper (1) with tip of fender (18) in area of headlamp | Press against bumper (1) in area of bumper guard and not on cover Bumper (1) should not extend more than 1 mm beyond tip of fender (18) | |
16 | Tighten screw (4) | ||
17 | Start screws (8) loosely | ||
18 | Push intermediate layer (17) outward to stop | This closes the gap between the bumper (1) and cross member. Move intermediate layer (17) with only slight force to prevent bumper (1) from being pressed forward | |
19 | Align bumper (1) to correct height and tighten nuts (12) | ||
| |||
20 | Tighten screws (8) | ||
21 | Screw in screw (11) | The flange on the telescoping nozzle (10) should make contact with the reinforcement frame for the bumper (1) | |
22 | Install cover (9) on telescoping nozzle (10) | ||
23 | Plug in connector for fog lamp (3) | ||
24 | Install outside temperature sensor (5) | ||
25 | Install spreading rivet (6) in rear wheelhouse panel | ||
26 | Install lining (2) |
Gap dimensions for bumper
Number | Designation | Models 208.3/4 | ||
BE88.20-P-1003-01A | Di-men-sion | Front bumper, gap dimension "C" | mm | 6 |
See figure | ||||
Bumper
Number | Designation | Models 208.3/4 | |
BA88.20-P-1001-01A | Nut for front bumper on cross member | Nm | 20 |
BA88.20-P-1003-01A | Bolt for front bumper on headlamp housing | Nm | 2 |
BA88.20-P-1004-01A | Bolt for front bumper on inside of fender | Nm | 3 |
Feeler gage
129 589 03 21 00