Remove/install right cylinder head cover

AR01.20-D-5012US

Remove/install right cylinder head cover

2.11.11

 

Remove/install

1

Remove air filter housing

AR09.10-D-1150US

2

Remove ignition coils

AR15.12-D-2003US

3

Remove front cover at cylinder head (2)

AR01.30-D-5700UV

4

Remove cover from centrifuge

AR01.20-D-2120US

5

Disconnect right electrical connector at ME-SFI [ME] control unit (N3/23)

6

Pull out ME-SFI [ME] control unit (N3/23) upwards and put to one side

7

Remove right control unit holder (9)



*BA07.08-N-1002-01A

8

Remove oil dipstick guide tube (3) on cylinder head cover (1)

9

Remove ground line (4) on cylinder head cover (1)

10

Disconnect electrical connectors (6, 10)

11

Remove feed duct (8) to cylinder head cover (1) on resonance intake manifold and to lifting eye (7), place to one side and secure with cable tie



*BA15.18-N-1001-01D



*BA15.18-N-1002-01D



*BA15.18-N-1003-01D

12

Remove cylinder head cover bolts (1) in the reverse order of the tightening procedure

AR01.20-D-5014-03US



*BA01.30-N-1003-01R

13

Detach and remove cylinder head cover (1) carefully from cylinder head (2)

 Heat up cylinder head cover (1) if necessary in the area of the sealing surface using a hot air gun and pry off the cylinder head (2) using a suitable tool.

Electric plastic hot air blower
gotis://K_60-65_11.0

 Installation: Do not use any sharp edged tools or emery cloth to clean otherwise damages can occur to the sealing surfaces.

 Installation: Clean sealing surfaces on cylinder head cover (1) and on cylinder head (2) using adhesive and sealant remover.

Apply sealant to cylinder head cover (1). Observe application of sealant.



*112589002500

Loctite 5970 sealant

*BR00.45-Z-1013-01A

Loctite 7200

*BR00.45-Z-1038-04A



Notes on sealant path for cylinder head cover

AH01.30-N-1000-08US

14

Remove cap (5) from cylinder head (2)

 Installation: Check cap (5), replace if necessary. Only push in cap (5) after tightening the cylinder head cover (1).

15

Remove holder on cylinder head cover (1)

 When replacing cylinder head cover (1).

16

Install in the reverse order

 Danger!

Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running

Secure vehicle to prevent it from moving by itself.
Wear closed and snug-fitting work clothes.
Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

17

Perform engine test run and check engine in the area of the cylinder head cover (1) and front cover on cylinder head (2) for leaks

Number

Designation

Engine
272.979
in model
906

BA01.30-N-1003-01R

Bolt, cylinder head cover to cylinder head

M7

Stage 1

Nm

12

Stage 2

°

90

Number

Designation

Engine
272.979
in model
906

BA07.08-N-1002-01A

Bolt, control unit bracket to resonance intake manifold

Nm

10

Number

Designation

Engine
272
in model
906

BA15.18-N-1001-01D

Bolt, feed duct to resonance intake manifold

Nm

8

BA15.18-N-1002-01D

Bolt, feed duct to cylinder head cover

Nm

8

BA15.18-N-1003-01D

Bolt, feed duct to engine suspension lug

Nm

8

Number

Designation

Order number

BR00.45-Z-1013-01A

Loctite 5970 sealant

A 003 989 98 20

BR00.45-Z-1038-04A

Loctite 7200

Henkel Loctite Deutschland GmbH
Arabellastrasse 17
81925 München
Germany
Tel. +49 899268-0
Fax + 49 899101978
www.Loctite.de