B35.10-0010-09
1 | Anti-roll bar | 11 | Rubber pad | |
2 | Guide upper plate | 12 | Nut | |
3 | Spring clip | 13 | Shock absorber | |
4 | Breather hose | 14 | Combination cylinder connections | |
5 | Nut | 15 | Wear indicator | |
6 | Screw | 16 | Terminal | |
7 | Clamp | 17 | Protective cover | |
8 | Propeller shaft | 18 | Actuation cable | |
9 | Screw | 19 | Screws | |
10 | Torsion bar clamp | 20 | Cylinder lines |
1 | Anti-roll bar |
4 | Breather hose |
5 | Nut |
12 | Nut |
13 | Shock absorber |
17 | Protective cover |
B35.10-0005-02
| Remove/install | ||
1 | Remove the rear wheels |
| |
2 | Drain the oil from the rear axle housing | ||
| . | ||
3 | Release the clamp and remove the breather hose (4) on the axle side | ||
4 | Depressurize the pneumatic system at the tanks | ||
5 | Disconnect the sensor end piece (16) with white cable and remove cable plug screw from the brake pad worn indicator (15) | Installation: Install the new screw. | |
6 | Loosen the flexible pipe connections from the combined cylinders (14) | Installation: Install new seal washers. | |
7 | Loosen the clamp and move the combined cylinder line (20) and the brake pad wear sensor harness away from the shaft | ||
8 | Unscrew the screws (19) and loosen the drive cable (18) from the brake force control valve | ||
9 | Unscrew the nuts (12), loosen the lower eyes of the shock absorbers (13) and the torsion bar clamps (10) from the supports | Installation: Install new self-locking nuts | |
Check rubber bushing conditions of the shock absorbers and torsion bar. | |||
Rear shock absorbers' nuts | |||
10 | Loosen the coupling fork on the rear axle side and secure the propeller shaft (8) to the chassis | Pre-mark the original position between the propeller shaft and shaft coupling forks to maintain balance. | |
Propeller shaft attachment | |||
11 | Insert an appropriate lifting device under the rear axle and lift it slightly | Do not lift the vehicle from the differential housing. | |
12 | Remove the protective cover (17) and the nut and tilt the brake saddle together with the combined cylinder | Required for removing the spring U-screw nut, combined cylinder side. | |
Mounting bolt to mount caliper on axle | |||
13 | Loosen the nuts (5) and remove the spring U-screws (3), the upper guide plates (2) and the lower plate of the spring U-screws | Installation: Clean the "U" screw threads and lubricate. | |
Spring "U" bolt | |||
14 | Lower the shaft and remove it | ||
15 | Install in reverse order |
Rear axle shock absorbers |
Number | Designation | Model 688 | ||
BA32.25-B-1001-03A | Rear shock absorbers' nuts | M12x1.5 | Nm | - |
M14x15- steel 8 | Nm | 108 | ||
M14x1,5 (ISO) | Nm | - | ||
M16x1,5 - steel 8 | Nm | - | ||
M16x1,5 - with flange | Nm | - | ||
M16x1.5 | Nm | - | ||
M16x2 (ISO) | Nm | - | ||
M20x1,5 - steel 8 | Nm | - | ||
M20x1,5 - steel 10 | Nm | - | ||
M24x2- steel 10.9 | Nm | - |