Replace COC papers and vehicle identification plate (code: VS4TYPCOC) · sm0010s0050a · Mercedes-Benz WIS

SM00.10-S-0050A

Replace COC papers and vehicle identification plate (code: VS4TYPCOC)

14.08.2018

Model

470.2## ## as of 000002 up to 021099

Operation no. of the operation texts or standard texts and flat rates
Category	Op. no.	Operation text	Time	Acc. no.	Code
P	02 2427	Operations: Replace COC papers and vehicle identification plate	-	58 917 51	VS4TYPCOC

Replace COC papers and vehicle identification plate (code: VS4TYPCOC)

1	Cap
2	Cap
3	Sealing frame
4	Right front door
5	Instrument panel
6	Vehicle identification plate
7	Right A-pillar

S00.10-4520-06

6	Vehicle identification plate
8	Heat protection
9	Vehicle body tape

S00.10-4521-11

Topical note	Notes on carrying out repair work in the vehicle interior		AH68.00-N-0001-01S
	Check
1	Check whether vehicle is affected by measure.	 Only the entry in the ExtendedVEGA Application (EVA) system in the "Current" tab is significant for authorized Mercedes-Benz service partners. An additional test of the affected vehicles in the workshop information system (WIS) or vehicle list is thereby not necessary.
	Replace
2	Ask customer to hand over old Certificate of Conformity (COC) documents.	 Customer must hand over the original old Certificate of Conformity *COC (documents(.
3	Determine approval situation/status of the vehicle and issue active message, and coordinate further measures.	 Following coordination, the original old COC documents must be sent to the following address: Daimler AG MercedesBenz Düsseldorf Plant Plant: 065 In-house post code (HPC): PS41 Department: VAN/OSD 40467 Düsseldorf Germany The new COC documents will only be delivered by the Düsseldorf plant after the original old COC documents have been returned.
		For Germany only
		
		Further steps for applying for new COC documents (including active message through vehicle registration situation/status) are to be coordinated per email (coc[email protected]). Always state the company-owned sales and service outlet/service partner dealer number in the email.
		not for Germany
		
		Contact technical wholesales level (MPC) or general distributor (GV) to request new COC documents and coordinate additional steps. The technical wholesales level (MPC) or general distributor (GV) can proceed as for Germany (coordination per email, see above).
		If the request for new COC documents has been met with positive feedback.
		
		proceed with operation step 4.
4	Hand new original COC documents to customer.	 Do not hand them out without first having the original old COC documents returned.
	Remove
5	Remove covers (1, 2).	 Long wedge	*115589035900
6	Partially loosen sealing frame (3) of right front door (4) along the working area.
7	Cover plastic parts of instrument panel (5) and right front door (4) with heat protection (8) in the working area.	 Cover surrounding component parts in the working area with heat protection (8). Otherwise, the component parts in the working area can be damaged as a result of heat exposure.
	Replace
8	Heat up vehicle identification plate (6) uniformly.
	000 588 00 84 00 Heat gun		WS54.00-P-0049B
		 Do not overheat vehicle identification plate (6). This prevents damage to the paint from overheating.
		 In some vehicles, two vehicle identification plates (6) can be glued on top of each other.
9	Loosen a corner of the vehicle identification plate (6) using a suitable tool.
10	Mark position of old vehicle identification plate (6) (e.g. using body tape (9)).	 Immediately after marking the position, begin the next operation step. Otherwise the working area that was previously heated cools down and it becomes more difficult to remove the old vehicle identification plate (6).
11	Remove vehicle identification plate (6) at right A-pillar (7) using a suitable tool.	 In some vehicles, two vehicle identification plates (6) can be glued on top of each other.
12	Clean bonding area of the vehicle identification plate (6) with silicone remover.	 The bonding area of the vehicle identification plate (6) must be absolutely free of dust and grease. Otherwise there may be adhesion problems.
		 Do not clean beyond the bonding area of the vehicle identification plate (6).
		Silicone remover, order No. 893222600	*BR00.45-Z-1060-04A
13	Replace vehicle identification plate (6) at right A-pillar (7).	 Reattach new vehicle identification plate (6) exactly at marked position.
	Install
14	Remove previously-applied marking.
15	Remove heat protection (welding pearl catcher) (8).	 Welding bead catcher	*129589019800
16	Secure sealing frame (3) of right front door (4).	 Do not use any lubricant. Otherwise leakage is not possible.
		 Ensure that sealing frame (3) is seated correctly.
17	Install covers (1, 2).

115 589 03 59 00

Long wedge

129 589 01 98 00

Welding bead catcher

Repair materials

Number	Designation	Order number
BR00.45-Z-1060-04A	Silicone remover, order No. 893222600	Adolf Würth GmbH & Co. KG Reinhold-Würth-Str. 12-17 74653 Künzelsau-Gaisbach Germany Tel. +49 7940 15-0 Fax +49 7940 15-1000 http://www.wuerth.de

Parts ordering note

Part no.	Designation	Quantity
A 470 584 99 01 26	Vehicle identification plate (please quote vehicle identification number when ordering)	1

Referenced documents

ah6800n000101s Notes on carrying out repair work in the vehicle interior
ws5400p0049b 000 588 00 84 00 Heat gun