Model | 204.9 |
up to model year 2013 | |
with code 614 (Bi-xenon headlamps) | |
Model | 204.9 |
up to model year 2013 | |
with code 615 (Bi-xenon headlamps with active light function) | |
Up to model year 2013 | |
Model | 204.9 |
up to model year 2013 | |
with code 616 (Bi-xenon headlamp unit with integrated asymmetric curve illumination) | |
Model | 204.9 |
up to model year 2013 | |
with code 621 (Intelligent Light System (left-hand traffic)) | |
Model | 204.9 |
up to model year 2013 | |
with code 622 (Intelligent Light System) |
P82.10-5576-08
Shown on the left front lamp unit (E1) |
1 | Screw | E1 | Left front lamp unit | E1n4 | Left xenon light power supply module | ||
2 | Electrical connectors | E2 | Right front lamp unit | E2n4 | Right xenon light power supply module | ||
3 | Seal |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines. | |
Danger | Risk of explosion/risk of fire caused by highly flammable materials in the vicinity of damaged xenon bulbs. Risk of injury caused by UV light, hot components on xenon headlamps and glass splinters produced by bursting xenon bulbs. Risk of poisoning caused by inhalation of mercury vapors and by swallowing of/skin contact with toxic salts and mercury compounds. | Do not touch parts conducting high voltage. Persons with active electronic implants (e.g. cardiac pacemakers) must never work on xenon headlamps. Switch off the entire lighting system. Wear insulated safety shoes, safety glasses and protective gloves. Remove highly inflammable materials from the danger zone. Ensure sufficient ventilation in the working area. | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
| Remove/install | ||
1 | Carry out initial startup of left xenon light power supply module (E1n4) or right xenon light power supply module (E2n4) | Only when replacing left xenon light power supply module (E1n4) or right xenon light power supply module (E2n4). | |
| Connect STAR DIAGNOSIS and read out fault memory | ||
2 | Switch off ignition and remove transmitter key or KEYLESS-GO start/stop button from electronic ignition lock control unit | ||
3 | Lift vehicle on vehicle lift | ||
4 | Release left fender liner in vicinity of bumper and lift out fender liner with assembly wedge | When removing left xenon light power supply module (E1n4). | |
Mounting wedge | |||
5 | Release right fender liner in vicinity of bumper and lift out fender liner with assembly wedge | When removing right xenon light power supply module (E2n4). | |
Mounting wedge | |||
6 | Remove bolt (1) | ||
7 | Remove left xenon light power supply module (E1n4) or right xenon light power supply module (E2n4) | Installation: Make sure that seal (3) is seated correctly. | |
8 | Separate electrical connectors (2) | ||
9 | Install in the reverse order |
110 589 03 59 00
Mounting wedge
Referenced documents
- ad0000p200004a Connect STAR DIAGNOSIS and read out fault memory
- ad0000p200004a
- ah5400p000101a Information on preventing damage to electronic components due to electrostatic discharge
- as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
- as0000z003501a Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)
- as8210z000101a Risk of explosion/risk of fire caused by highly flammable materials in the vicinity of damaged xenon bulbs. Risk of injury caused by UV light, hot components on xenon headlamps and glass splinters produced by bursting xenon