Remove/install taillamp reinforcement

AR63.20-P-2011MEC

Remove/install taillamp reinforcement

07.05.2019

Model

167.3

1

Connecting panel

2

Rear lamp reinforcement

 Danger

Risk of death caused by vehicle slipping or toppling off of the lifting platform.

Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.

AS00.00-Z-0010-01A

 Warning

Risk of injury. Skin or eye injuries may result when handling hot or glowing objects.

Wear protective gloves, protective clothing and safety glasses, if necessary.

AS00.00-Z-0002-01A

 Caution

Risk of injury caused by scraping or cutting body parts on sharp vehicle parts

Always wear protective gloves when working on or near sharp and non-deburred vehicle parts.
Deburr repair panels.

AS00.00-Z-0017-01A

Topical note

Information on preventing damage to electronic components due to electrostatic discharge

AH54.00-P-0001-01A

Topical note

General information on body repair

AH60.00-N-0001-01A

General information on MB materials

AH98.00-P-9409-03A



Remove

1

Remove detachable parts in area of repair point.

2

Cover all detachable parts remaining in vehicle with spark protection blankets.

3

Remove connecting panel (1) and rear lamp reinforcement (2).

AR63.20-P-2011-01MEC

1K-zinc dust paint

*BR00.45-Z-1056-07A



Install

 Danger

The high voltage used for electric welding presents a lethal hazard. Risk of explosion from welding in areas close to highly inflammable materials. Risk of injury from weld splatter and UV-light when welding. Risk of poisoning from inhaling welding gases

Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system.

AS00.00-Z-0007-01A

Topical note

Measures for preventing damage to components when performing electric welding and soldering work

AH60.00-P-0001-02A

General information on riveting

AH60.00-P-0003-01N

4

Prepare connecting panel (1) and rear lamp reinforcement (2) for installation.

AR63.20-P-2011-02MEC

1K-zinc dust paint

*BR00.45-Z-1056-07A

5

Install connecting panel (1) and rear lamp reinforcement (2).

AR63.20-P-2011-03MEC

1K-zinc dust paint

*BR00.45-Z-1056-07A

Blind rivet 6.512.5 (clamping range 2 mm to 5 mm, draw-off strength min. 19 kN)

*BR00.45-Z-1012-13A

Blind rivet 6.412 (clamping range 1 mm to 3.5 mm, draw-off strength min. 15.5 kN)

*BR00.45-Z-1035-13A

Blind rivet with countersunk head 6.414.0 (clamping range 1.5 mm to 3 mm, draw-off strength min. 15.5 kN)

*BR00.45-Z-1043-13A

Blind rivet with countersunk head 6.415.5 (clamping range 3 mm to 5 mm, draw-off strength min. 15.5 kN)

*BR00.45-Z-1044-13A

6

Clean weld joints and sheet metal flange.

7

Remove spark protection blankets.

8

Clean repair area.

9

Prime repair areas using a primer filler.

Topical note

Notes on paintwork repairs

AH98.00-P-9408-02A

 Use only primer filler approved by Daimler AG:
https://xentryportal.i.daimler.com

10

Seal seam after repair.

AR97.10-P-4000ME

11

Paint repair areas and adjacent surfaces.

Topical note

Notes on paintwork repairs

AH98.00-P-9408-02A

 Use only paints approved by Daimler AG:
https://xentryportal.i.daimler.com

12

Supplement cavity preservation

AR97.20-P-1500ME

13

Install all detachable parts in area to be repaired.

Repair materials

Number

Designation

Order number

BR00.45-Z-1012-13A

Blind rivet 6.512.5 (clamping range 2 mm to 5 mm, draw-off strength min. 19 kN)

A 004 990 16 97

BR00.45-Z-1035-13A

Blind rivet 6.412 (clamping range 1 mm to 3.5 mm, draw-off strength min. 15.5 kN)

A 000 991 76 32

BR00.45-Z-1043-13A

Blind rivet with countersunk head 6.414.0 (clamping range 1.5 mm to 3 mm, draw-off strength min. 15.5 kN)

A 000 991 82 32

BR00.45-Z-1044-13A

Blind rivet with countersunk head 6.415.5 (clamping range 3 mm to 5 mm, draw-off strength min. 15.5 kN)

A 000 991 83 32

BR00.45-Z-1056-07A

1K-zinc dust paint

A 000 986 28 00