Shown on model 907.6, left side of vehicle |
1 | Upper front longitudinal member |
D62.20-0128-05
Shown on model 907 with engine 651 |
2 | Ventilation box |
3 | Windshield wiper system for windshield |
4 | Hose |
5 | Frame seal |
6 | Electrical wiring harness |
7 | Passage grommet |
8 | Vapor barriers |
9 | Ground lines |
10 | Engine hood cable |
11 | Diesel injection system control unit |
12 | Electrical wiring harness |
13 | Passage grommet |
14 | Vapor barriers |
D60.00-A021-06
Danger | Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC) | Do not touch damaged or defective live component parts and lines or non-insulated electrical connections and lines.Model 910 with engine 780.703 | |
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Topical note | General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment | Model 910 with engine 780.703 | |
Topical note | Information on preventing damage to electronic components due to electrostatic discharge | ||
Topical note | Notes on carrying out repair work in the vehicle interior | ||
| Remove/install | ||
1 | Remove hood. | ||
2 | Remove respective front door. | ||
3 | Remove windshield. |
| |
Model 907, 910 | |||
4 | Remove front-end assembly. | ||
5 | Remove respective front section of front fender liner. | ||
6 | Remove respective rear section of front fender liner. | ||
7 | Remove respective front fender. | ||
8 | Remove hose (4) and position outside the working area. | If left side of vehicle is damaged. | |
9 | Remove windshield wiper system for windshield (3). | In the case of damage at driver's side. | |
10 | Remove ventilation box (2). | In the case of damage at front passenger side. | |
Model 907 with engine 274 | |||
11 | Remove sealing frame (5) in repair area and position outside the working area. | ||
12 | Remove electrical wiring harness (6) and position outside the working area. | If left side of vehicle is damaged. | |
13 | Remove feed-through grommet (7) in repair area and position outside the working area. | If left side of vehicle is damaged. | |
14 | Remove dampings (8) in repair area and position outside the working area. | If left side of vehicle is damaged. | |
15 | Remove ground lines (9) and position outside the working area. | If left side of vehicle is damaged. | |
M6 | |||
16 | Remove hood cable (10) at hood catch lower section and position outside the working area. | If left side of vehicle is damaged. | |
| |||
17 | Remove diesel injection system control unit (11). | If left side of vehicle is damaged. | |
Model 907 with engine 642 | |||
18 | Remove electrical wiring harness (12) in repair area and position outside the working area. | If right side of vehicle is damaged. | |
19 | Remove feed-through grommet (13) in repair area and position outside the working area. | If right side of vehicle is damaged. | |
20 | Remove dampings (14) in repair area and position outside the working area. | If right side of vehicle is damaged. | |
21 | Install in the reverse order. |
Referenced documents
- ah0000z030001a General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment
- ah5400p000101a Information on preventing damage to electronic components due to electrostatic discharge
- ah6800n000101s Notes on carrying out repair work in the vehicle interior
- ar0708d7009tsr Remove/install diesel fuel injection system control unit
- ar6000d0023ts Remove/install front end
- ar6710d1700ts Remove, install windshield
- ar6710d1700tsb Remove, install windshield
- ar7210d0500ts Remove/install front door
- ar8230d0002ts Remove/install windshield wiper system for windshield
- ar8310d0010ts Removing, installing ventilation housing
- ar8810d1005ts Remove/install front fender
- ar8810d1321ts Remove/install rear section of front fender liner
- ar8810d1322ts Remove/install front section of front fender liner
- ar8840d3000ts Remove/install engine hood
- as0000z001001a Risk of death caused by vehicle slipping or toppling off of the lifting platform.
- as0000z003501a Risk of death when working on component parts and systems with U >= 30 V alternating voltage (AC) or U >= 60 V direct voltage (DC)