Shown on model 447 with code H12 (Auxiliary water heater) |
1 | Fuel tank |
2 | Screw |
3 | Screw |
4 | Grommet |
5 | Fuel lines |
6 | Fuel line |
7 | Retaining bracket |
8 | Bolts |
10 | Ground cable |
S47.10-4524-06
1 | Fuel tank |
9 | Electrical connector |
S47.10-4525-01
Danger | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. | |
Danger | Risk of explosion caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel. | No fires, sparks, open flames or smoking. Pour fuels into suitable and appropriately marked containers only. | |
Danger | Risk of explosion caused by fuel vapors igniting, risk of poisoning caused by inhaling combustible gases and risk of injury caused by burns during and after operation of heater unit | Do not operate stationary heater, auxiliary heater or engine with heater booster in closed rooms or when refueling. Allow heater unit to cool down after operation and wear protective gloves. | |
Topical note | Notes on avoiding damage through contamination and foreign objects | ||
| Remove/install | ||
1 | Empty the fuel tank (1). | ||
2 | Remove fuel filler flap. | ||
3 | Remove screw (2). | ||
4 | Remove screw/bolt (3) and swivel bracket away out of working area | ||
5 | Release filler neck from the body. | ||
6 | Remove covers at vehicle jack lift support points. | Model 447 with engine 651 | |
7 | Raise vehicle. | ||
8 | Remove underfloor paneling at left. |
| |
Model 447 with engine 651 | |||
9 | Remove grommet (4). | The grommet (4) remains on the filler neck. | |
Installation: Check grommet (4) for damage. | |||
If damage is identified, | |||
| |||
replace grommet (4). | |||
10 | Release and disconnect fuel lines (5) and collect escaping fuel. | Installation: Note assignment of the fuel lines (5). | |
11 | Seal openings in fuel lines (5) with the stop plugs. | Record plug | |
12 | Disconnect fuel line (6) and collect escaping fuel. | Model 447 with engine 622, 651, 654.9 | |
Installation: Replace clamp. | |||
Pliers for click clamps | |||
13 | Seal openings in fuel line (6) with the stop plugs. | Record plug | |
14 | Support fuel tank (1). | ||
| 000 588 10 62 00 Support plate | ||
| 000 588 11 62 00 Major assembly mount | ||
Secure the fuel tank(1) against falling down. | |||
15 | Remove screws (8) and remove mounting frame bows (7). | ||
Topical note | Notes on using electrical or pneumatic screwdrivers/impact wrenches | ||
Installation: Reposition shims of retaining brackets (7) in previous installation position. | |||
Retaining bracket, fuel tank to longitudinal member | |||
16 | Lower the fuel tank (1) until electrical connector (9) is accessible. | ||
17 | Release and disconnect electrical connection(9). | ||
18 | Continue lowering the fuel tank (1) until the ground line (10) is accessible. | ||
19 | Remove ground line (10) on filler neck. | ||
20 | Lower fuel tank (1) completely and remove. | | |
21 | Remove the fuel pump and fill level sensor. | If the fuel tank (1) is replaced: | |
22 | Install in the reverse order | ||
| Check | ||
23 | Switch on ignition. | | |
Warning | Risk of burn injuries, suffocation and poisoning when working on the exhaust system and the components connected to it. Risk of suffocation and risk of poisoning caused by inhalation of gaseous and solid components of the exhaust. Risk of poisoning caused by skin contact with solid components of the exhaust. | Wear protective clothing and safety glasses. Use the extraction system. Move people out of the hazard area. | |
Warning | Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug-fitting work clothes. Do not touch hot or rotating parts. | |
24 | Check fuel system for leak tightness with engine running. |
129 589 00 91 00
Record plug
171 589 00 37 00
Pliers for click clamps
Έγγραφα που αναφέρονται
- ah0000n001701a Οδηγίες για τη χρήση ηλεκτρικών ή πνευματικών κατσαβιδιών
- ah0000p500001a Υποδείξεις για την αποφυγή ζημιών από ακαθαρσίες και ξένα σώματα
- ar0060s1000e
- ar4710s4001e Εκκένωση, πλήρωση ρεζερβουάρ καυσίμου
- ar4720s7000e Αφαίρεση, τοποθέτηση αντλίας καυσίμου και αισθητήρα στάθμης πλήρωσης
- ar6130s100104e
- ar6130s1001e
- ar6130s1001eh
- ar8860s6023e Αφαίρεση, τοποθέτηση τάπας ρεζερβουάρ καυσίμου
- as0000z000501a Κίνδυνος ατυχήματος λόγω αυτόματης εκκίνησης κατά τη λειτουργία του κινητήρα. Κίνδυνος τραυματισμού με μώλωπες και εγκαύματα σε �
- as0000z001001a Θανάσιμος κίνδυνος λόγω ολίσθησης ή ανατροπής του οχήματος από το αναβατόριο
- as4700z000101a Kίνδυνος εκρήξεως εξαιτίας αναφλέξεως, κίνδυνος δηλητηριάσεως εξαιτίας εισπνοής και πόσεως καυσίμων, καθώς επίσης κίνδυνος τραυμ
- as4900z000101a Κίνδυνος εγκαύματος, ασφυξίας και δηλητηρίασης σε εργασίες στο συγκρότημα καυσαερίων και στα σχετιζόμενα εξαρτήματα. Κίνδυνος ασ
- as8370z000201a Kίνδυνος εκρήξεως από ατμούς καυσίμων, κίνδυνος δηλητηριάσεως από εισπνοή αερίων καύσεως και κίνδυνος τραυματισμού από εγκαύματα
- ws0100p0092b 000 588 11 62 00 Βάση μηχανικών συγκροτημάτων
- ws2600p3309b 000 588 10 62 00 Πλάκα στήριξης