AZ83.70-W-0007A | Retrofitting Trumatic E 2400 air heater unit | 20.6.97 |
BODY 940.899 with CODE (F04) L-cab (long)
BODY 940.899 with CODE (DD5) Cab with high roof
BODY 972.899 with CODE (F04) Cab L (long)
BODY 972.899 with CODE (DD5) Cab with high roof
W83.70-1014-09
1 Timer (expansion)
2 Separating coupling, cab - frame
3 Gas supply pipe
7 Air heater
8 Control module
9 Operating element (standard)
4 Shut-off cock
5 Pressure controller, gas bottle
6 Gas bottle holder
| Removing | ||
Danger! | Risk of explosion due to leaking LPG and fuel vapors. Risk of poisoning from inhaling combustion gases. | Close valve of gas cylinder in closed areas. Do not operate air heater in closed areas or when refueling. | |
1 | Disconnect ground lead from battery | ||
2 | Remove trim panels in driver's footwell and to left and right of steering column | ||
3 | Remove glove compartment | ||
4 | Remove trim panel underneath glove box | ||
5 | Remove brackets and control modules in front passenger footwell and store | ||
6 | Remove fuse board | Do not disconnect lines. | |
7 | Move driver's seat as far forward as possible | ||
8 | Fold lower bunk up and secure | ||
9 | Remove storage shelf from bunk box behind driver's seat | ||
10 | Loosen floor covering in heater installation area and move to side | ||
| Installing | ||
| Information regarding LPG installations | ||
11 | Provide openings for exhaust stack and gas supply | ||
Corrosion protection | |||
12 | Install exhaust stack | ||
Sealant | |||
13 | Install heater | ||
Sealant | |||
14 | Route gas supply pipe | Heater - separating coupling | |
| |||
15 | Fit separating coupling | ||
16 | Install control electronics and connect | ||
17 | Install operating element | In place of the operating element, which only allows manual switching on and off, a timer with programmable switching on times can be installed. | |
18 | Install timer | ||
19 | Install warm air duct | ||
Corrosion protection | |||
20 | Install gas bottle holder | ||
Corrosion protection | |||
21 | Route gas supply pipe | Separating coupling - gas bottle | |
| |||
Corrosion protection | |||
22 | Check gas supply for leaks | ||
| |||
23 | Install gas bottle and connect | ||
24 | Switch on heater according to operating instructions and carry out functional checks i.a.w. manufacturers specifications | ||
25 | Fit remaining parts to vehicle | ||
26 | Pull protective hoods over separating coupling and bottle valve | If the protective hood for a separating coupling is fitted with a pull cord t provide protection during tipping of the cab, remove it | |
| Information for retrofitting a stationary heater with LPG combustion |
Pipe bending device
000 589 39 31 00
Commercially available tools
Number | Designation | |
WH58.30-Z-1030-13A | Pressure pump with pressure gauge (for checking leaktightness of liquified gas systems) |
Repair materials
Number | Designation | Order number |
BR00.45-Z-1014-01A | Adhesive tape | A 000 989 98 85 |
Parts ordering notes
Part no. | Designation | Quantity |
B6 731 1100 | Basic unit Trumatic E 2400/24 V, 30 mbar | 1 |
B6 731 1041 | Installation kit, Atego, with L or LH cab | 1 |
Henviste dokumenter
- ah8370n000107a Oplysninger om eftermontering af parkeringsvarme med forbrænding med flydende gas
- ah8370n000108a Oplysninger om montering af anlæg med flydende gas
- as8370z000401a Fare for eksplosion på grund af udsivende flydende gas og brændstofdampe. Fare for forgiftning på grund af indånding af forbrændingsgasser
- az8370w000202e
- az8370w000205d
- az8370w000208f
- az8370w000301c
- az8370w000701a
- az8370w000702a
- az8370w000703a
- az8370w000703b
- az8370w000704a
- az8370w000705a
- az8370w000706a
- az8370w000707a
- az8370w000708a