AR18.40-W-4133A | Remove/install oil pressure/oil temperature sensor | 29.10.08 |
ENGINES 904.904 ## as of 040488 in MODEL 670
ENGINES 904.908 ## as of 040488 in MODELS 668, 670
ENGINES 904.914 /923 /936 in MODELS 668, 670
ENGINES 904.9## ## as of 040488 in MODELS 673, 674, 676
ENGINES 904.9## ## up to 301576 in MODELS 375, 958, 970, 972, 975, 976
ENGINES 906.9## ## up to 301561 in MODELS 958, 970, 972, 974, 975, 976
ENGINES 906.9## ## up to 301561 in MODELS 375, 950, 952, 953, 954, 958
ENGINES 906.9## ## up to 301561 in MODEL 957 except CODE (MS8) Natural gas engine
ENGINES 902.9, 906.9 in MODEL 957 with CODE (MS8) Natural gas engine
W18.40-1014-02
1 Electrical connector
2 Oil filter cover
B102 Oil combination sensor (models 668, 670)
B110 Oil pressure and oil temperature combination sensor (models 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976)
| Remove/install | ||
1 | Switch off ignition | ||
Danger! | Risk of injury caused by body parts being pinched or crushed as cab is tilted | Ensure that no one is within tilting range of cab as it is being tilted. Always tilt cab all the way to end position and secure with safety strut. | |
2.1 | Tilt cab | Models 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976 | |
For model 957, open front flap and unlock steering wheel adjustment. | |||
Installation: Tilt the cab back after the leak test has been conducted | |||
| Notes on tilting the cab | ||
2.2 | Remove service cover | Model 668, 670 | |
3 | Remove right soundproofing on frame | Only for models 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976 | |
4.1 | Detach exhaust manifold at the turbocharger | Models 375, 668, 670, 950, 952, 953, 954, 958, 970, 972, 974, 975, 976 | |
4.2 | Remove air intake hose | Model 668, 670 | |
5 | Unscrew oil filter cap (2) from oil filter housing | When oil filter cover (2) is unscrewed, the engine oil flows back into the oil pan. | |
Installation: Replace sealing ring on oil filter cover (2). | |||
| |||
6 | Disconnect electrical connector (1) | ||
7.1 | Remove oil combination sensor (B102) | Model 668, 670 | |
Collect engine oil that flows out. | |||
| |||
7.2 | Remove oil pressure and oil temperature combination sensor (B110) | Models 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976 | |
Collect engine oil that flows out. | |||
| |||
8 | Install in the reverse order | ||
9 | Check engine oil level using oil dipstick or on display, correct if necessary | Observe engine oil grade set in maintenance system or Specifications for Operating Fluids. | |
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. | |
10 | Start engine | Do not rev up engine before oil pressure is indicated. The oil pressure gauge must indicate oil pressure after about 10 seconds. | |
11 | Switch off engine and check for leaks | Visual inspection. |
Check values for engine oil pressure
Number | Designation | Engines | ||
BE18.00-N-1001-01C | Engine oil pressure at | Idling speed | bar | 0.5 |
maximum speed | bar | 2.5 | ||
Oil filter
Number | Designation | Engines | |
BA18.20-N-1003-01B | Oil filter cover to oil filter housing | Nm | 25 |
Oil level sensor, oil pressure sensor
Henviste dokumenter
- ah6080n000301a Oplysninger om tipning af førerhus
- ar0910d8030d
- as0000z000501a Fare for ulykke ved automatisk igangsætning når motoren kører. Fare for personskade på grund af knusning og forbrænding, hvis der arbejdes mens motoren startes eller kører
- as6080z000101a Fare for personskade ved fastklemning og knusning, når førerhuset tippes