ar2000p1142sm

Drain/fill in coolant

Typ ar · téma 20.00 · verze 0200 · 2008-02-29

Platí pro: ENGINE 160.910 in MODEL 450.3 /4 up to WME01MCO12H106037 ENGINE 160.920 in MODEL 450.3 /4 as of WME4503001J000001 ENGINE 660.940 in MODEL 450.3 /4

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 1 Motor › 20 Chlazení motoru › 20.00 Všeobecné — Řada 450 (modely 3**, 4**) · Řada 660 (modely 940)

EinPAS 15 Motor › 15.25 Chladicí systém motoru › 15.25.5 Kompletní okruh chlazení — Řada 450 (modely 3**, 4**) · Řada 660 (modely 940)

Platí také pro motory/převodovky: 160 910, 160 920

AR20.00-P-1142SM

Drain/fill in coolant

19.2.08

ENGINE 160.910 in MODEL 450.3 /4
up to WME01MCO12H106037

ENGINE 160.920 in MODEL 450.3 /4
as of WME4503001J000001

ENGINE 660.940 in MODEL 450.3 /4

Drain/fill in coolant

P20.00-2347-06

1 Cap

2 Expansion reservoir

3 Hose clamp

4 Coolant hose

Modification notes

1.2.08

The operation step to drain coolant from cylinder crankcase no longer applies

Drain

Danger!

Risk of injury to skin and eyes caused by scalding from contact with hot coolant spray. Risk of poisoning caused by swallowing coolant.

Do not open cooling system unless coolant temperature is below 90°C. Open cap slowly and release the pressure. Do not pour coolant into beverage containers.

Wear protective gloves, protective clothing and safety glasses.

AS20.00-Z-0001-01A

Notes on coolant

AH20.00-N-2080-01A

1.1

Remove air inlet

On model 450.3/4 except 450.418

AR83.25-P-1401SM

1.2

Open windshield

In case of model 450.418

2

Turn cooling system cap (1) on engine radiator (2) a half turn counterclockwise, relieve the pressure and then unscrew the cooling system cap (1)

3

Remove underfloor panels

AR61.30-P-1001SM

4

Loosen hose clamp (3) on coolant hose (4), detach coolant hose (4) from radiator and drain off coolant

Catch coolant in a suitable vessel.

Filling

5

Position coolant hose (4) on radiator and fix in place with a hose clamp (3)

Replace hose clamp (3).

6

Lower vehicle with vehicle lift

7

Pour in coolant and bleed cooling system

AR20.00-P-1142-06SM

*450589072100

*450589206300

Coolant specifications

Sheet 310.1

BB00.40-P-0310-01A

Anticorrosion/antifreeze agents (Sheet 325.0)

Sheet 325.0

BB00.40-P-0325-00A

8

Seal expansion reservoir (2) with cap (1)

Checking

Danger!

Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running

Secure vehicle to prevent it from moving by itself.
Wear closed and snug-fitting work clothes.
Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

9

Run engine until warm

Until the coolant fan motor cuts in.

10

Turn cooling system cap (1) on engine radiator (2) a half turn counterclockwise, relieve the pressure and then unscrew the cooling system cap (1)

11

Check coolant level in the expansion reservoir (2) and correct if necessary

The engine coolant level in the coolant expansion reservoir (2) must be positioned at the max. marking.

Coolant specifications

Sheet 310.1

BB00.40-P-0310-01A

Anticorrosion/antifreeze agents (Sheet 325.0)

Sheet 325.0

BB00.40-P-0325-00A

12

Seal expansion reservoir (2) with cap (1)

13

Raise vehicle with vehicle lift

14

Install underfloor paneling

AR61.30-P-1001SM

15.1

Install air inlet

On model 450.3/4 except 450.418

AR83.25-P-1401SM

15.2

Close windshield

In case of model 450.418

Drain/fill in coolant
Drain/fill in coolant

450 589 20 63 00

Filling device

Pressure pump

450 589 07 21 00

Odkazované dokumenty