ar0145d7500f

Remove/install oil pan

Typ ar · téma 01.45 · verze 0109 · 2011-10-31

Platí pro: ENGINES 611.981 /987 in MODEL 901.6, 902.6, 903.6, 904.6 ENGINES 611.983 in MODEL 690.6

Není k dispozici v jazyce „cs“; zobrazeno v jazyce Angličtina.

Zařazení

Funkční skupina 1 Motor › 01 Motor kompletní, odvětrání motoru, hlava válců, kliková skříň › 01.45 Olejová vana — Řada 611 (modely 981, 983, 987) · Řada 690 (modely 6**) · Řada 901 (modely 6**) · Řada 902 (modely 6**) · Řada 903 (modely 6**) · Řada 904 (modely 6**)

EinPAS 15 Motor › 15.15 Kompletní spalovací motor/blok motoru/klikový mechanismus › 15.15.43 Olejová vana/plnicí hrdlo — Řada 611 (modely 981, 983, 987) · Řada 690 (modely 6**) · Řada 901 (modely 6**) · Řada 902 (modely 6**) · Řada 903 (modely 6**) · Řada 904 (modely 6**)

AR01.45-D-7500F

Remove/install oil pan

21.10.11

ENGINES 611.981 /987 in MODEL 901.6, 902.6, 903.6, 904.6

ENGINES 611.983 in MODEL 690.6

Remove/install oil pan

D01.45-1102-09

1 Oil pan

2 Seal

3 Plug for oil level sensor

4 Cable duct for alternator line set

8 Bow

9 Screw/bolt

10 Engine lifting device

5 Screw/bolts

6 Screw/bolts

7 Stabilizer

Remove/install

1

Drain engine oil, pour in

AP18.00-D-0101A

2

Detach anti-roll bar (7) at front axle and turn down

Installation: Replace self-locking nut.

*BA32.35-N-1001-02E

3

Detach cable duct (4) for generator wiring harness on left and right at crankcase, release from oil pan Screw/bolts and push to the side

4

Carefully raise engine with engine lifting device (10) until it abuts at the ventilation duct cover

Lowering: When lowering, place engine lightly onto engine mount, screw in Screw/bolts and tighten by hand until they make contact. Subsequently lower engine fully and tighten Screw/bolts to the final torque.

AR22.10-D-1260-01C

WBM 0307.02 (do not reorder)

Engine support device, engine hoist
gotis://A_01_09.0

*BA22.10-N-1002-01L

5

Unplug connector (3) at oil level sensor

6

Remove screw/bolts (6) and screw/bolts (5) for oil pan (1)

The bolt in bore (A) cannot be taken out and must be inserted before installation in the oil pan.

Installation: First screw in all Screw/bolts initially, then tighten fully.

Pay attention to different lengths and diameters of Screw/bolts!

Bolt plan for oil pan

AR01.45-D-7500-06D

*BA01.45-N-1001-01H

*BA01.45-N-1002-01H

*BA01.45-N-1004-01H

*BA01.45-N-1005-01H

7

Take off oil pan (1) together with oil pan gasket (2)

Installation: Clean sealing surfaces.

Replace oil pan gasket (2) and coat places labeled with blue mark (arrows) with sealant.

*BR00.45-Z-1013-01A

8

Install in the reverse order

Danger!

Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running

Secure vehicle to prevent it from moving by itself.
Wear closed and snug-fitting work clothes.
Do not touch hot or rotating parts.

AS00.00-Z-0005-01A

9

Inspect for oil leaks

Allow engine to run until warm, then turn off engine and check for leaks

Oil pan

Number

Designation

Engine 611.981/
983/987

BA01.45-N-1001-01H

Screw/bolt, oil pan to cylinder crankcase

M6

Nm

9

M8

Nm

20

M10

Nm

-

BA01.45-N-1002-01H

Screw/bolt, transmission bell housing to oil pan

Nm

40

BA01.45-N-1004-01H

Screw/bolt, oil pan to end cover

Nm

9

BA01.45-N-1005-01H

Screw/bolt, oil pan to timing case cover

M6

Nm

9

Engine mounts, engine supports

Number

Designation

Engine 611.981/
983/987

BA22.10-N-1002-01L

Screw/bolt, engine bracket to front engine mount

Nm

83

Front axle anti-sway bar

Number

Designation

Model 690, 901, 902, 903, 904

BA32.35-N-1001-02E

Bolt or nut, anti-roll bar bearing shell to front axle beam

M8

Nm

30

Repair materials

Number

Designation

Order number

BR00.45-Z-1013-01A

Loctite 5970 sealant

A 003 989 98 20

Odkazované dokumenty