Convert vehicles to emissions standard EEV

AN00.10-W-2000A

Convert vehicles to emissions standard EEV

09.09.2015

Model

930 with engine 541.970/971/972/973/974/975/976/977/980/981

with code KD6 (Exhaust gas monitor for nitrogen oxides (NOx))

with code MS5 (BlueTec 5)

Retrofit code (MS7) BlueTec EEV

Model

932 with engine 541.970/971/972/973/974/975/976/977/980/981

with code KD6 (Exhaust gas monitor for nitrogen oxides (NOx))

with code MS5 (BlueTec 5)

Retrofit code (MS7) BlueTec EEV

Model

933 with engine 541.970/972/974/976/980

with code KD6 (Exhaust gas monitor for nitrogen oxides (NOx))

with code MS5 (BlueTec 5)

Retrofit code (MS7) BlueTec EEV

Model

934 with engine 541.970/971/972/973/974/975/976/977/980/981

with code KD6 (Exhaust gas monitor for nitrogen oxides (NOx))

with code MS5 (BlueTec 5)

Retrofit code (MS7) BlueTec EEV

Information

1

SI00.10-W-0026ANote



SI00.10-W-0026A

 For further Information on the conversion.

Change

2

Order parts packages

 When ordering the parts packages, the vehicle identification number and the engine number must be specified. A password is required to perform the download for the engine control (MR) control unit. The password is determined by a hotline. Before the hotline is contacted, the data for the vehicle to be converted must be updated in VeDoc; otherwise, it is not possible to convey the password.
To request the password the form "Password request for conversion to EEV, Form" must be filled in and transmitted by email to the VeDoc email address specified on it.

3

Connect diagnostic system

 The diagnostic system is required for several operation steps.

4

Replace injection lines, connection fittings and injection nozzles



AR07.03-W-6831G

5

Attach new engine model plates to timing case and oil filter module

 Vehicles with code M78 (Engine number, embossed)
The digits to be altered on the embossed engine type must rendered illegible by embossing "X" over them and replaced with new digits.

6

Document conversion in VeDoc



SM00.10-W-0007-02B

7

Change data record, software and parameters in the engine control (MR) control unit



SM07.15-W-0005C



Password request for conversion from Euro 5 to EEV, Form

OF00.10-N-3000-04A

8

Attach information label to engine control (MR) control unit

9

Replace old BlueTec 5-labels on cab by new BlueTec EEV labels

10

Carry out test stand run



Modification instruction for EOL fine correction Y values, form

OF00.10-N-3000-05A

 Carry out test stand run as per the instructions in the performance test stand folder.
As long as no reference curves for EEV vehicles are stored in the engine dynamometer folder, the reference curves of the original engine model designation on the engine dynamometer folder must be used. If EOL values are adapted, these new values must be transmitted via the form to the VeDoc email address specified on it.

11

Detach diagnostic system

12

Apply for manufacturer certification of conversion

 For Germany, the required manufacturer certification can be requested here:
Daimler AG Homologation (TP/EVA)
70546 Stuttgart
Germany
Telephone 0711-1752093
Fax 0711-1723494
E-mail: [email protected]

Outside Germany, contact the relevant MPC/general distributor.

Parts ordering note

Part no.

Designation

Quantity

A 000 584 00 78

Parts kit information package

1

A 003 010 08 51

Parts kit for EEV

1