SI20.20-G-0006B | Service Information: Optimization of left radiator swivel angle | 29.10.08 |
ENGINE 902.923 /924 in MODEL 405.103 /123 /201 /221
with CODE (E33) Battery disconnect switch
with CODE (E87) Equipment socket (32-pin)
The position of the additional compressed air reservoir on vehicles with battery disconnect switch, code (E33) or the position of the equipment socket 32-pin, code (E87) restricts the left radiator's swivel range.
The following conversion enables accessibility to the radiator to be improved to simplify cleaning of the radiator.
Cost settlement:
The costs for the conversion are to be borne by the customer.
G20.20-3205-08
Previous radiator swivel range
A Approx. 60 mm (with code (C47) Rear radiator grill)
Radiator swivel range optimized
A Approx. 110 mm (with code (C47) Rear radiator grill)
G20.20-3202-09
Shown with code (E33) Battery disconnect switch and code (E87) Equipment socket 32-pin
1 Bracket
2 Ø 5 mm hole
9 Radiator grill
Dimensions:
A 30 mm
X10/1 Equipment socket (32-pin)
3 Screw
4 Retaining screw
5 Compressed air reservoir
6 Tensioning strap
7 Screw
8 Screw
G14.40-3249-11
Shown with code (E33) Battery disconnect switch, code (E87) Equipment socket 32-pin and code (E90) ISOBUS preparation or code (E91) ISOBUS with terminal
10 Bracket
X99 Left center implement ISOBUS socket
X102 ISOBUS camera socket
G14.40-3250-01
Shown with code (E90) ISOBUS preparation or code (E91) ISOBUS with terminal
10 Bracket
Dimensions:
B 15 mm
C 10 mm
D 50 mm
G14.40-3251-01
G14.40-3247-11
Depiction of converted version with code (E33) Battery disconnect switch and code (E87) Equipment socket 32-pin
G14.40-3248-11
Depiction of converted version with code (E33) Battery disconnect switch, code (E87) Equipment socket 32-pin and code (E90) ISOBUS preparation or code (E91) ISOBUS with terminal
| Notes on self-locking nuts and bolts | All models | |
1 | Raise and secure dumper flatbed | See the Operator's Manual . | |
2 | Remove equipment socket, 32-pin (X10/1) from bracket (1) | Only with code (E87) Equipment socket 32-pin | |
3 | Remove ISOBUS socket for left center implement (X99) and ISOBUS camera socket (X102) from bracket (10) | Only with code (E87) Equipment socket 32-pin in combination with code (E90) ISOBUS preparation or code (E91) ISOBUS with terminal | |
4.1 | Remove bolts (3) and remove bracket (1) | Only with code (E87) Equipment socket 32-pin | |
4.2 | Remove bolts (3) and remove bracket (10) | Only with code (E87) Equipment socket 32-pin in combination with code (E90) ISOBUS preparation or code (E91) ISOBUS with terminal | |
5 | Move equipment socket, 32-pin (X10/1) as far as possible to right (approx. 30 mm) and scribe mark new Ø 5 mm holes (2) on bracket (1) | Only with code (E87) Equipment socket 32-pin | |
6 | Drill four new Ø 5 mm holes (2) into the bracket (1) | Only with code (E87) Equipment socket 32-pin | |
7 | Shorten bracket (1) (arrow) | Only with code (E87) Equipment socket 32-pin Observe dimension (A). | |
8 | Debur and paint bracket (1) | Only with code (E87) Equipment socket 32-pin | |
9 | Make cutout in bracket (10) and bevel the edge | Only with code (E87) Equipment socket 32-pin in combination with code (E90) ISOBUS preparation or code (E91) ISOBUS with terminal Note dimensions (B, C, D). | |
10 | Debur and paint bracket (10) | Only with code (E87) Equipment socket 32-pin in combination with code (E90) ISOBUS preparation or code (E91) ISOBUS with terminal | |
11 | Remove retaining screw (4) from compressed air reservoir (5) | Only with code (E33) Battery disconnect switch | |
Remove cable ties on compressed air lines. | |||
12 | Release tensioning strap (6) and remove compressed air reservoir (5) | Only with code (E33) Battery disconnect switch | |
13 | Remove screws (7, 8) and remove bracket for compressed air reservoir (5) | Only with code (E33) Battery disconnect switch | |
14 | Insert new screws (7, 8) | Only with code (E33) Battery disconnect switch | |
Replace screw (7) with screw M1025 and screw (8) with screw M1030. To insert the screws (7, 8), the AdBlue tank has to be carefully pushed to one side using a tire iron. | |||
15 | Fit several shims to screw (8) | Only with code (E33) Battery disconnect switch | |
This serves to ensure that the compressed air reservoir (5) has a new installation position. Use shims with a total thickness of approx. 10 mm. | |||
16 | Install bracket for compressed air reservoir (5) | Only with code (E33) Battery disconnect switch | |
17.1 | Install bracket (1) and turn in screws (3) | Only with code (E87) Equipment socket 32-pin | |
Replace self-locking nuts. | |||
17.2 | Install bracket (10) and turn in screws (3) | Only with code (E87) Equipment socket 32-pin in combination with code (E90) ISOBUS preparation or code (E91) ISOBUS with terminal | |
Replace self-locking nuts. | |||
18 | Install compressed air reservoir (5) | Only with code (E33) Battery disconnect switch | |
19 | Screw retaining screw (4) into compressed air reservoir (5) | Only with code (E33) Battery disconnect switch | |
| |||
20 | Fasten tensioning strap (6) into place | With code (E33) Battery disconnect switch | |
Replace self-locking nut. Position compressed air reservoir (5) as close as possible to frame. | |||
21 | Fasten compressed air lines into place using cable ties | Only with code (E33) Battery disconnect switch | |
22 | Mount ISOBUS socket for left center implement (X99) and ISOBUS camera socket (X102) onto bracket (10) | Only with code (E87) Equipment socket 32-pin in combination with code (E90) ISOBUS preparation or code (E91) ISOBUS with terminal | |
Replace self-locking nuts. | |||
23 | Install equipment socket, 32-pin (X10/1) onto bracket (1) | Only with code (E87) Equipment socket 32-pin | |
24 | Remove radiator grill (9) | Only with code (C47) Rear radiator grill | |
25 | Press radiator grill (9) in area of compressed air reservoir (5) (hatched area) in under a press | Only with code (C47) Rear radiator grill | |
To avoid damaging the radiator slats, the radiator grill (9) must not be pressed-in too far. | |||
Support radiator grill (9) at outside using two wooden blocks. To press in use a wooden block. Press in radiator grill (9) by max. 10 mm. | |||
26 | Install radiator grill (9) | Only with code (C47) Rear radiator grill | |
Replace self-locking nuts. | |||
27 | Release and lower dumper flatbed | See the Operator's Manual . |
Compressed air lines