AR83.70-D-5399B | Removing heater from housing, installing | 4.11.96 |
MODEL 901.06#, 902.06# /07#, 903.06# /07#, 904.06# ## up to 753730 up to 31.10.97 with CODE (H11) Hot air auxiliary heater
Heater designation B3L-C
MODEL 901.36# /37# /46#, 902.36# /37# /46# /47#, 903.36# /37# /46# /47#, 904.36# ## up to 753730 up to 31.10.97,
904.46 up to 31.10.97 with CODE (H11) Hot air auxiliary heater
Heater designation D3L-C
D83.70-0039-06
1 Heater
2 Housing center section
3 Left end panel
4 Right end panel
5 Cover
6 Bracket
7 Control module
8 Fuel metering pump
9 Rubber grommet
10 Rubber grommet
11 Pipe clamp
12 Screw
13 Washer
14 Nut
15 Philips screw
16 Plastic washer
17 Connector
D83.70-0037-06
18 Flange
19 Flange gasket
20 Cap
21 Combustion air hose
22 Exhaust pipe
23 Pipe clamp
24 Hex. head bolt
25 Nut
26 Hose clamp
27 Heater mounting nut
28 Washer
29 Adapter
30 Hose clamp
31 Fuel line
| Removal, installation | ||
Danger! | Fuel vapors present an explosion hazard. Combustion gases are toxic when inhaled. Heater can cause severe burns during and after operation | Do not start up or operate stationary heaters or engines with heater boosters in closed rooms or in the vicinity of service stations. Allow heater to cool off after operation and wear protective gloves. | |
Danger! | Fuel vapors present an explosion hazard. Fuel vapors are toxic when inhaled or absorbed. Contact with fuel can cause eye and skin injury. | Fire, open lights and smoking prohibited. Wear protective clothing when handling fuel. | |
1 | Remove heater | Models 901.06, 902.06/07, 903.06/07, 904.06 | |
Models 901.36/37/46, 902.36/37/46/47, 903.36/37/46/47, 904.36/46 left-hand steering | |||
Models 901.36/37/46, 902.36/37/46/47, 903.36/37/46/47, 904.36/46 right-hand steering | |||
2 | Remove connector (17) | Bayonet connection | |
3 | Press rubber grommet (9) out of right end panel (4) | ||
4 | Remove right end panel (4) | ||
5 | Remove left end panel (3) | ||
6 | Unscrew bracket (6) and pull toward front | ||
7 | Disconnect electrical connectors from control module (7) | ||
8 | Unscrew fuel metering pump (8) from bracket (6) and remove bracket | ||
9 | Pull cap (20) off of combustion air hose (21) | ||
10 | Remove combustion air hose (21) from flange (18) | Installation: Observe installation position, angle of mounting clamp | |
11 | Remove exhaust pipe (22) from flange (18) | Installation: Observe installation position, angle of mounting clamp | |
12 | Remove fuel line (31) from flange (18) | Installation: Observe installation position, angle of mounting clamp | |
13 | Unscrew heater mounting nuts (27) and remove washers (28) | ||
14 | Pull heater (1) forward until pipe clamp (11) is accessible | ||
15 | Remove pipe clamp (11) | ||
16 | Completely remove heater (1) | ||
17 | Remove flange gasket (19) | Installation: Check flange gasket for damage, replace if necessary. | |
18 | Install in opposite order |