Remove/install floor covering

AR68.20-W-2040C

6.3.06

MODEL 374.502 /523 /551 /554 /557 /584 with BODY 374.860

MODEL 374.602 /651 /655 /682 /685 with BODY 374.870

MODEL 375.1 with BODY 375.850

MODEL 375.3 with BODY 375.820

MODEL 375.4 with BODY 375.860

MODEL 374.607 /691 /695, 940, 942, 943, 944 with BODY 944.890

MODEL 950.5 /6, 952.5 /6, 953.6, 954.5 with BODY 940.890

MODEL 958.0 with BODY 958.860

MODEL 958.2 with BODY 958.870

MODEL 958.4 with BODY 958.880

MODEL 970, 972, 974, 975, 976 with BODY 972.890

W68.20-1016-11

Shown on body 972.890

1 Engine tunnel floor covering

2 Support rod

3 Paneling

4 Edge protection strip

5 Driver side floor covering

6 Sensor unit cover (only on vehicles with code (GE1) Automatic gear control (AGS))

7 Level control operating device

A93 Automatic gear control (AGS) shift control unit (only on vehicles with code (GE1) Automatic gear control (AGS))

W68.20-1017-11

Shown on body 972.890

1 Engine tunnel floor covering

2 Support rod

3 Paneling

4 Edge protection strip

8 Floor covering on passenger side

 	Remove/install
1	Remove front seats	Model 374, 375, 940, 942, 943, 944, 950.5/6, 952.5/6, 953.6, 954.5, 970, 972, 974, 975, 976	AR91.10-W-1000A
		Model 958	AR91.10-W-1000B
2	Remove support rod (2) from B-pillar	 The support rod (2) is inserted into paneling (3) at bottom on wheelhouse	AR68.70-W-0303C
3	Remove paneling (3) from wheelhouse	 Disconnect electrical connector from level control operating device (7)
4	Remove edge protection strip (4)
5	Remove driver side floor covering (5) and passenger side floor covering (8)
6.1	Remove automatic gear control (AGS) shift control unit (A93)	Vehicles with code (GE1) Automatic gear control (AGS)	AR26.60-W-0012D
		 Installation: Check whether connector on automatic gear control (AGS) shift control unit (A93) is seated correctly
6.2	Remove gear control shift control unit	Vehicles with code (GS2) Gear control	AR26.60-W-0012E
		 Installation: Check whether connector on gear control shift control unit is seated correctly.
6.3	Remove gearshift lever cover	Vehicles without code (GS2) Gear control and without code (GE1) Automatic gear control (AGS)
7	Remove sensor unit cover (6)	Only on vehicles with code (GE1) Automatic gear control (AGS) or code (GS2) Gear control
8	Remove stowage compartment from center module	Vehicles with code (FN1) Distributor vehicle cockpit	AR68.10-W-1624A
		Vehicles with code (FN2) Comfort cockpit	AR68.10-W-1624B
		Vehicles with code (FN3) Long-distance haulage vehicle cockpit	AR68.10-W-1624C
9	Remove engine tunnel floor covering (1)
10	Remove stowage box/tray from rear wall paneling	Only on vehicles with code (F04) L cab (long)	AR68.30-W-4755E
11	Remove rear floor covering	Only on vehicles with code (F04) L cab (long)
12	Install in the reverse order

เอกสารที่อ้างถึง