P68.10-2621-09
7 Instrument panel
8 Glove compartment
9 Cover on center console
10 Cover below instrument panel on left
11 Cover below instrument panel on right
12 Jacket tube cover
21 Ashtray housing
22 Right instrument panel cover
23 Left instrument panel cover
24 Center air nozzle
TO1 Instrument cluster
N7-1 Light module
13 Ignition lock trim ring
14 Steering column module
15 Right front door air nozzle
16 Left front door air nozzle
17 Left side air nozzle
18 Right side air nozzle
19 Trim strip
20 Stowage compartment
P68.10-2003-06
1-6 Screws
7 Instrument panel
25 Cross member below instrument panel
| Remove | ||
1 | Remove electronic ignition switch control module | Remove out of instrument panel toward front Do not disconnect electrical connectors and shift lock pull cable | |
| |||
2 | Move selector lever to position "D" | Insert electronic ignition key into ignition/starter switch | |
3 | Disconnect ground cable of battery | ||
4 | Remove cover (10) below instrument panel on left | ||
5 | Disconnect electrical connector from data link connector | On left below instrument panel. | |
6 | Remove jacket tube module (14) | ||
7 | Remove cover (12) below jacket tube | ||
8 | Remove instrument cluster (A1) | ||
9 | Remove light module (N7-1) | ||
10 | Remove paneling from left and right A-pillars | ||
11 | Remove glove compartment (8) | ||
12 | Remove trim strip (19) | ||
13 | Remove left (17) and right (18) side air nozzles | ||
14 | Unclip right (15) and left (16) front door air nozzles from instrument panel (7) | ||
15 | Remove cover (11) below instrument panel on right | ||
16 | Remove cover (9) from center console | ||
17 | Remove center air nozzle (24) | ||
18 | Unclip right (22) and left (23) covers from instrument panel | ||
19.1 | Remove Parktronic displays | with Parktronic system (code 220a) | |
20 | Unscrew screws (1-6) from instrument panel | ||
21 | Lift instrument panel (7) | ||
22 | Unclip loudspeaker from center of instrument panel (7) | Only disconnect connector | |
23 | Lift instrument panel (7) out through open passenger door | Danger of damaging instrument panel | |
24 | Lay instrument panel (7) down on suitable base | ||
| Install | ||
25 | Insert sheet metal clip nuts (6 each) in cross member (25) for mounting instrument panel (7) | ||
26 | Position instrument panel (7) in passenger compartment through open passenger door and install on cross member (25) | Danger of damaging instrument panel | |
27 | Clip loudspeaker into center of instrument panel (7) | Check seal above air outlet on heater housing, if necessary replace instrument panel (7) with defroster nozzles on heater housing | |
28 | Screw in screws (1-6) | ||
29 | Screw jacket tube cover (12) to instrument panel (7) | ||
30 | Clip right (22) and left (23) covers into instrument panel | ||
31 | Install Parktronic displays | with Parktronic system (code 220a) | |
32 | Install electronic ignition/starter switch control module | ||
| |||
33 | Clip right (15) and left (16) front door air nozzles into instrument panel (7) | ||
34 | Install left (17) and right (18) side air nozzles | ||
35 | Install center air nozzle (24) | ||
36 | Install cover (9) on center console | ||
37 | Install glove compartment (8) | ||
38 | Install cover (11) below instrument panel on right | ||
39 | Connect electrical connector for data link connector | On left below instrument panel. | |
40 | Install light module (N7-1) | ||
41 | Install jacket tube module (18) | ||
42 | Install instrument cluster (A1) | ||
43 | Install trim strip (19) | ||
44 | Install cover (10) below instrument panel on left | ||
45 | Install paneling on left and right A-pillars | ||
46 | Reconnect ground lead to battery | ||
47 | Carry out operational check | ||
48 | Read out fault memory | Star Diagnosis |
Claw-type wrench for ignition / starter switch trim ring
210 589 00 07 00