Shown on model 907 with code E30 (Battery master switch) |
1 | Ground cable |
2 | Trim |
3 | Electrical connector |
D54.10-1197-06
Shown on model 907 except code E30 (Battery master switch) |
1 | Ground cable |
2 | Trim |
4 | Nut |
D54.10-1198-06
Danger | Risk of fire/risk of explosion due to short circuit and escaping oxyhydrogen gas. Risk of (burn) injury caused by caustic burns to eyes, skin and mucous membranes from battery electrolyte/mist, short circuit and arcing. Risk of poisoning caused by swallowing battery electrolyte or absorption of lead through the skin or body orifices. Risk of death due to voltage U >= 30 V AC and U >= 60 V DC. | No fires, sparks, open flames, or smoking. Wear acid-resistant gloves, clothing, and glasses. Pour battery acid only into suitable and appropriately marked containers. | |
Topical note | General information on vehicles with high-voltage on-board electrical system and/or lithium-ion battery and/or gaseous-fuel drive system as well as personal protective equipment | Model 910 with engine 780.703 | |
Topical note | Notes on battery | ||
Topical note | Notes on carrying out repair work in the vehicle interior | ||
| Remove/install | ||
1 | Disconnect charging cable connector of high-voltage on-board electrical system and wait 30 s until power-down is complete. | Model 910 with engine 780.703 | |
2 | Disconnect charger from on-board electrical system battery. | When an external charger is connected. | |
3 | Move driver seat to rearmost position. | ||
4 | Switch off ignition and store transmitter key outside of transmission range (min. 2 m). | After the ignition has been switched off, a run-on time of approx. 2 min must be waited before disconnecting the ground line (1). | |
5 | Remove trim (2). | ||
6.1 | Release electrical connector (3) (arrow A) and disconnect in direction of arrow (arrow B) with ground line (1). | Model 907, 910 | |
Removal: Position the ground line (1) so that there is no inadvertent contact with vehicle ground. | |||
6.2 | Remove nut (4) and remove ground line (1). | Model 907, 910 | |
Removal: Position the ground line (1) so that there is no inadvertent contact with vehicle ground. | |||
Nut, ground line to body | |||
| Check | ||
7 | Check for absence of voltage on 12 V on-board electrical system. | Model 910 | |
| Service Information: Determine absence of voltage of 12 V on-board electrical system after removing the ground or positive line of the on-board electrical system battery | ||
| 000 588 07 19 00 Measuring instrument | ||
The engine hood must be closed. Observe the Service Information. | |||
8.1 | Expose fuse holder at driver's seat and remove fuse F32 at fuse slot 32 of driver's seat fuse holder. | Model 907 | |
| Assignment of fuse holders on seat base | ||
| |||
Installation: When commissioning the vehicle, make sure that an intact 10 A fuse F32 is installed again in fuse slot 32 of the driver's seat fuse holder. | |||
8.2 | Expose fuse and relay module on front passenger side then remove fuse F30-6 from fuse slot 6 of plug S16 on front passenger side fuse and relay module. | Model 910 with engine 780.703 | |
Remove/install vehicle tool kit carrier plate | |||
| Assignment of passenger-side footwell fuse and relay module | ||
| |||
Installation: When commissioning the vehicle, make sure that an intact 10 A fuse F30-6 is inserted into fuse slot 6 of the plug S16 on the passenger-side fuse and relay module. | |||
9 | Install in the reverse order. | ||
Adjust | |||
10 | Set time and date in instrument cluster. | ||
11 | Adjust weekday, time and default value of operating time on warm air stationary heater switch clock. | Model 907.6/7 | |
See Owner's Manual. |