Shown on model 405.050 with steering LS6BK |
1 | Steering gear |
2 | Primary shaft |
3 | Cover |
4 | Boot (with steering LS6BK) |
5 | Universal joint |
Pfeil A | Mark |
Pfeil B | Mark |
Pfeil C | Mark |
Pfeil D | Slot |
G46.20-3150-06
Shown on MODEL 405.121 with steering LS6BK |
1 | Steering gear |
2 | Primary shaft |
3 | Cover |
4 | Boot (with steering LS6BK) |
5 | Universal joint |
Pfeil A | Mark |
Pfeil B | Mark |
Pfeil C | Mark |
Pfeil D | Slot |
G46.20-3147-06
Shown on model 405.121 with steering ZF 8095 |
1 | Steering gear |
2 | Primary shaft |
3 | Cover |
5 | Universal joint |
Pfeil A | Mark |
Pfeil B | Mark |
Pfeil C | Mark |
Pfeil D | Slot |
G46.10-3153-06
Shown on model 405.123 with steering ZF 8098 |
1 | Steering gear |
2 | Primary shaft |
3 | Cover |
5 | Universal joint |
Pfeil A | Mark |
Pfeil B | Mark |
Pfeil C | Mark |
Pfeil D | Slot |
G46.10-3160-06
7 | Steering knuckle arm |
8 | Drag link |
9 | Pitman arm |
G46.40-3122-01
Danger | Risk of death caused by vehicle slipping or toppling off during lifting | Only lift vehicle at the lift support points specified by the vehicle manufacturer. | |
Topical note | Notes on installation position of universal joints on steering | ||
Topical note | Notes on self-locking nuts and bolts | ||
| Check | ||
1 | Raise front axle and lower onto jack stands | The wheels must move easily. | |
2 | Check steering knuckle and steering joints for ease of movement | To check, turn the wheel to the left and right by hand. | |
In the event of complaints | |||
| |||
Repair steering knuckle or steering joint. | |||
3 | Raise front axle, remove jack stands and position front wheels onto turntables | ||
4 | Correct tire inflation pressure | ||
| |||
5 | Check wheel angle taking into account the tire size and tire clearance | ||
If a problem arises | |||
| |||
Adjust wheel angle. | |||
6 | Check toe | ||
If a problem arises | |||
| |||
Adjust toe-in. | |||
7 | Move wheels to straight-ahead position | ||
8 | Remove left front fender | Model 405.102/103/122/123/200/201/220/221with steering ZF 8098 | |
9 | Check whether there is a cover (3) on the steering gear (1) | Model 405.050/100/101/102/103/120/121/122/123/200/201/220/221with steering LS6BK | |
If there is no cover (3) or boot (4). | |||
| |||
Detach steering shaft with universal joint (5), install cover (3) or boot (4) and mount steering shaft with universal joint (5) again. | |||
| |||
| |||
| |||
Nut, universal joint to steering gear | |||
Bracket, steering shaft bearing to mounting console for cab mount | |||
Long-life grease | |||
10 | Check that the markings (arrows A, B) line up with the marking (arrow C) | | |
If the markings (arrows A, B) line up with marking (arrow C) | |||
| |||
Proceed with operation step 18. | |||
If the markings (arrows A, B) do not line up with marking (arrow C) | |||
| |||
Adjust center steering position on steering gear (1); to do so, perform operation steps 11 to 20. | |||
Adjust | |||
11 | Detach drag link (8) from steering knuckle arm (7) | ||
12 | Check straight-ahead position of wheels | If a problem arises | |
| |||
Move wheels to straight-ahead position. | |||
13 | Move pitman arm (9) from end stop to end stop, and count number of turns on primary shaft (2) while doing so | ||
14 | By moving the pitman arm (9), turn back the primary shaft (2) by half the value of the turns counted from one end stop, and then align | The markings (arrows A, B) must line up with the marking (arrow C). | |
15 | Adjust length of drag link (8) and mount onto steering knuckle arm (7) | ||
| Check | ||
16 | Check position of slot (arrow D) on universal joint (5) | Model 405.050/100/101/102/103/120/121/122/123/200/201/220/221 | |
Model 405.102/103/122/123/200/201/220/221with steering ZF 8098 | |||
If a problem arises | |||
| |||
Correct position of universal joint (5). | |||
| |||
| |||
| |||
Nut, universal joint to steering gear | |||
Bracket, steering shaft bearing to mounting console for cab mount | |||
Long-life grease | |||
17 | Check straight-ahead position of steering wheel | If a problem arises | |
| |||
Move steering wheel by shifting it into straight-ahead position. | |||
| |||
| |||
18 | Install left front fender | ||
19 | Raise front axle, remove turntables and lower vehicle | ||
20 | Conduct a road test | Check the entire steering behavior of the vehicle. |