W26.50-1083-09
1 Tapered roller bearing
2 Circlip
3 Sliding sleeve
4 Synchronizer body
5 Synchronizer cone
6 Synchronizer ring
7 Thrust spring
8 3rd gear wheel
9 Needle roller bearing
19 Synchronizer body
20 Synchronizer cone
21 Thrust spring
22 Synchronizer ring
23 1st gear wheel
24 Needle roller bearing
25 Main shaft
33 Shift unit
34 Tensioning device
10 Circlip
11 Washer
12 Needle roller bearing
13 2nd gear wheel
14 Thrust spring
15 Synchronizer ring
16 Synchronizer cone
17 Circlip
18 Sliding sleeve
W26.50-1084-11
25 Main shaft
26 Needle roller bearing
27 Crawler gear wheel
28 Synchronizer body
29 Sliding sleeve
30 Reverse gear wheel
31 Needle roller bearing
32 Tapered roller bearing
35 Circlip
36 Sleeve
37 Sun gear
38 Circlip
| Disassemble | ||
1 | Disassemble transmission | ||
2 | Clamp main shaft (25) in tensioning device (34) and remove and remove lifting device | Clamping device | |
Retainer | |||
3 | Remove, disassemble shift unit (33) and check for wear | ||
4 | Remove sliding sleeve (3) | ||
5 | Remove tapered roller bearing (1) | Hand pump | |
Hydraulic hose (complete) | |||
Adapter | |||
Adapter | |||
Hydraulic cylinder | |||
Gripper | |||
6 | Remove circlip (2) | ||
7 | Remove synchronizer body (4) | In the event of sluggishness, move in using suitable tools on both sides and pry off. | |
8 | Remove synchronizer ring (6) with annular spring (7) and synchronizer cone (5) from 3rd gear gear wheel (8) | ||
9 | Remove 3rd gear gear wheel (8) with needle roller bearing (9) | ||
10 | Remove circlip (10) | ||
11 | Remove washer (11) and 2nd gear gear wheel (13) | If it is difficult to remove, use three-arm puller. | |
| |||
12 | Remove needle roller bearing (12). | ||
13 | Remove synchronizer ring (15) with annular spring (14) and synchronizer cone (16) | ||
14 | Remove sliding sleeve (18) | ||
15 | Remove circlip (17) | ||
16 | Remove synchronizer body (19) | If it is difficult to remove, use three-arm puller. | |
| |||
17 | Remove synchronizer ring (22) with annular spring (21) and synchronizer cone (20) from 1st gear gear wheel (23) | ||
18 | Remove 1st gear gear wheel (23) with needle bearing (24) | ||
19 | Turn over main shaft (25) in the tensioning device and clamp securely | Clamp on the toothing of the synchronizer body (19) of first/second gear in order not to damage the bearing surfaces of the needle bearings (12, 24). | |
Clamping device | |||
20 | Remove circlip (38) | ||
21 | Remove sun gear (37) | ||
22 | Remove (36) sleeve | ||
23 | Remove tapered roller bearing (32) | Hand pump | |
Hydraulic hose (complete) | |||
Gripper | |||
Adapter | |||
Adapter | |||
Hydraulic cylinder | |||
24 | Remove reverse gear gearwheel (30) and needle roller bearing (31). | ||
25 | Remove sliding sleeve (29) | ||
26 | Remove circlip (35) | ||
27 | Remove crawler gear gear wheel (27) with synchronizer body (28) | | |
28 | Remove needle roller bearing (26). | ||
29 | Assemble main shaft (25) |
652 589 00 33 21
Hydraulic hose (complete)
Hand pump
Tensioning device
Retainer
315 589 02 31 00
652 589 00 33 23
715 589 04 31 00
715 589 11 34 00
Adapter
Adapter
Gripper
Hydraulic cylinder
715 589 09 34 00
715 589 12 34 00
715 589 15 34 00
Gripper
715 589 21 34 00
Commercially available tools