1 | Front section of transmission housing |
2 | Bearing sleeve |
3 | Drive shaft |
4 | Locking plates |
5 | Bolts |
6 | Countershaft |
7 | Inner bearing race (only transmission 711.660 in model 906.1/2/6/7 with engine 642.992, transmission 711.670 in model 204 with engine 642, transmission 711.670 in model 207 with engine 651) |
8 | Bearing (only transmission 711.660 in model 906.1/2/6/7 with engine 642.992, transmission 711.670 in model 204 with engine 642, transmission 711.670 in model 207 with engine 651) |
9 | Bearing (only transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990, transmission 711.660 in model 906.1/2/6/7 with engine 646.985/986/989/990) |
10 | Retaining ring |
11 | Bearing |
D26.40-1164-06
| Notes on self-locking nuts and bolts | ||
| Remove | ||
1 | Remove transmission |
| |
Transmission 711.670 in model 204 with engine 642, 651 | |||
Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990 | |||
2 | Fasten transmission on assembly stand | ||
3 | Remove central clutch release bearing |
| |
Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990 | |||
4 | Disassemble transmission housing | ||
| Disassemble | ||
5 | Remove locking washers (4) | ||
6 | Press out drive shaft (3) | Drift | |
7 | Detach circlip (10) and press off bearing (11) | ||
8 | Remove radial shaft sealing ring of drive shaft (3) | ||
9.1 | Press out bearing (9) | Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990 | |
Drift | |||
9.2 | Press out bearing (8) | Transmission 711.660 in model 906.1/2/6/7 with engine 642.992 | |
The inner bearing race (7) of the bearing (8) is divided into two halves. The half on the drive side was removed when disassembling the transmission housing. | |||
Drift | |||
10 | Pry inner bearing race on output side (7) off countershaft (6) | Transmission 711.660 in model 906.1/2/6/7 with engine 642.992 | |
11 | Remove bearing bushing (2) of main shifter shaft | Internal extractor | |
Counter stay | |||
| Clean | ||
12 | Clean seats and bearing seats | Use clean, lint-free rag. | |
| Assemble | ||
13 | Press bearing (11) into drive shaft (3) and attach retaining ring (10) | Transmission 711.670 in model 204 with engine 642, 651 | |
Replace retaining ring (10). | |||
The chamfer on the outer bearing race must point towards the gear wheel. | |||
Drift | |||
14 | Press drive shaft (3) into transmission housing front section (1) up to end stop | Drift | |
15.1 | Press in bearing (9) up to end stop | Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990 | |
The chamfer on the outer bearing race must point towards the output. | |||
Drift | |||
15.2 | Press in bearing (8) up to end stop | Transmission 711.660 in model 906.1/2/6/7 with engine 642.992 | |
The chamfer on the outer bearing race must point towards the output. | |||
The drive-side inner bearing race is installed during assembly of the transmission housing. | |||
Drift | |||
16 | Press on output side inner bearing race (7) as far as the end stop on the countershaft (6) | Transmission 711.660 in model 906.1/2/6/7 with engine 642.992 | |
Drift | |||
17 | Press in bearing bushing (2) of the main shifter shaft as far as the end stop | Drift | |
18 | Install lock washers (4) | Bolt, locking plate for countershaft bearing, main shaft bearing or drive shaft bearing to transmission housing | |
19 | Install radial shaft sealing ring of drive shaft (3) | ||
| Install | ||
20 | Assemble transmission housing | ||
21 | Install central clutch release bearing |
| |
Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990 | |||
22 | Detach transmission from assembly stand | ||
23 | Install transmission |
| |
Transmission 711.670 in model 204 with engine 642, 651 | |||
Transmission 711.651 in model 906.1/2/6/7 with engine 646.984/985/986/989/990 |
711 589 04 15 00
Drift
000 589 33 33 00
Counter stay
716 589 02 15 00
Drift
711 589 15 15 00
Drift
000 589 25 33 00
Internal extractor
716 589 00 15 00
Drift