Disassemble/assemble range group

AR26.31-G-3200AD

25.04.2018

Transmission

715.366 in model 800

G26.31-3122-09

1	Planetary gear set with shift mechanism	9	Bearing pin	17	Radial shaft sealing ring
2	Sliding blocks	10	Pulse wheel	18	Pilot bushing
3	Shift fork	11	Radial shaft sealing ring	19	Drift
4	Shift rod with shift piston	12	Output flange	B18	Travel and speed rpm sensor
5	Range group cylinder	13	O-ring	A	Bores (in carrier ring)
6	Retaining ring	14	Pressure plate	B	Bores (in transmission housing rear part)
7	Ball bearing	15	Stretch bolt	C	Inscription
8	Housing (range group)	16	Carrier ring

8	Housing (range group)
20	Puller
21	Flat iron

W26.31-1036-06

8	Housing (range group)
22	Pulling device
23	Sleeve (pulling device)

W26.31-1037-06

	Disassemble
1	Remove range group.		AR26.31-G-3100AD
2	Remove travel and speed rpm sensor (B18).		AR26.19-G-0034AD
3	Remove output flange (12).		AR26.50-G-2000AD
4	Remove radial shaft sealing ring (11).		AR26.40-G-3841AD
5	Remove range group cylinder (5).		AR26.18-G-3100AD
6	Remove bearing pins (9).
7	Turn shift rod with shift piston (4) through 180° and pull out.
8	Remove housing (8) from planetary gear set with shift mechanism (1).	 Place a flat iron (21) between the  puller (20) and housing (8). The housing (8) can otherwise be damaged.
		 Puller	*715589133300
		 Hand pump	*652589003321
		 Hydraulic hose (complete)	*652589003323
		 Adapter	*715589113400
		 Threaded tool	*715589116300
		 Adapter	*715589123400
		 Hydraulic cylinder	*715589153400
9	Remove pulse wheel (10).
10	Remove retaining ring (6).
11	Remove ball bearing (7) from housing (8).
12	Remove radial shaft sealing ring (17) and pilot bushing (18).	 Internal extractor	*000589273300
		 Counter stay	*000589333300
13	Disassemble planetary gear set with shift mechanism (1)	Only if the planetary gear set with shift mechanism (1) is being repaired.
			AR26.50-G-3102AD
	Assemble
14	Assemble planetary gear set with shift mechanism (1).	Only if the planetary gear set with shift mechanism (1) has been disassembled.
			AR26.50-G-3102AD
15	Coat new radial shaft sealing ring (17) with lubricant and install up to contact using drift (19).	 Install radial shaft sealing ring (17) with the spring lock washer facing inward (oil side).
		Synthetic grease 50 g	*BR00.45-Z-1027-06A
		 Drift	*714589051500
16	Install pilot bushing (18) up to contact using drift (19).	 Drift	*714589051500
17	Install ball bearing (7) and retaining ring (6) in housing (8).
18	Install sliding blocks (2) in shift fork (3) and insert into planetary gear set with shift mechanism (1).	 The inscription (arrows C) on the shift fork (3) must point towards the output.
19	Align bores (A) in carrier ring (16) and bores (B) in housing (8) until they line up with each other.
20	Place housing (8) with ball bearing (7) on planetary gear set with shift mechanism (1).
21	Press on housing (8) using pulling device (22).	 Press on housing (8) up to contact of ball bearing (7).
		 Hand pump	*652589003321
		 Hydraulic hose (complete)	*652589003323
		 Adapter	*715589113400
		 Pulling device	*715589123300
		 Adapter	*715589123400
		 Hydraulic cylinder	*715589153400
22	Install shift rod with shift piston (4).	 The shift fork (3) must engage in the recess of the shift rod with the shift piston (4).
23	Coat thread of bearing pins (9) with sealant and screw in bearing pins (9).	 Shift fork bearing pin at transmission housing	*BA26.31-N-1001-01HA
		Loctite 5203 sealant	*BR00.45-Z-1015-01A
24	Install range group cylinder (5).		AR26.18-G-3100AD
25	Install pulse wheel (10) in housing (8).
26	Coat sealing lip on new radial shaft sealing ring (11) with lubricant and install radial shaft sealing ring (11).		AR26.40-G-3841AD
		Synthetic grease 50 g	*BR00.45-Z-1027-06A
27	Install output flange (12).		AR26.50-G-2000AD
28	Install travel and speed rpm sensor (B18).		AR26.19-G-0034AD
		 Travel and speed rpm sensor to transmission	*BA26.19-N-1009-01HA
29	Install range group.		AR26.31-G-3100AD