P07.52-2033-07
Shown on engine 271.8
4 Catalytic converter
G3/2 Oxygen sensor upstream of catalytic converter
G3/2x1 Electrical connector for oxygen sensor upstream of catalytic converter
G3/1 Oxygen sensor downstream of catalytic converter
G3/1x1 Electrical connector for oxygen sensor downstream of catalytic converter
P07.52-2018-06
Shown on engine 271.9
1 Bracket
2 Bracket
3 Balance resistor
4 Catalytic converter
G3/1 Oxygen sensor downstream of catalytic converter
G3/1x1 Electrical connector for oxygen sensor downstream of catalytic converter
G3/2 Oxygen sensor upstream of catalytic converter
G3/2x1 Electrical connector for oxygen sensor upstream of catalytic converter
| Remove/install | ||
Danger! | Risk of injury to skin and eyes caused by handling hot or glowing objects. | Wear safety gloves, protective clothing and safety glasses, if necessary. | |
Danger! | Risk of death caused by vehicle slipping or toppling off of the lifting platform. | Align vehicle between columns of vehicle lift and position four support plates at vehicle lift support points specified by vehicle manufacturer. | |
1 | Raise vehicle | ||
2 | Remove rear section of the lower engine compartment paneling | Model 204 | |
Model 172 | |||
Model 207, 212 | |||
Installation: Install engine compartment paneling only after engine test run. | |||
Oxygen sensor downstream of catalytic converter (G3/1) | |||
3 | Unclip and disconnect electrical connection for oxygen sensor downstream of CAT (G3/1x1) on bracket | Unclip electrical line for sensor from bracket (1). | |
4 | Remove oxygen sensor downstream of CAT (G3/1) from CAT (4) | Installation: Coat thread with paste. | |
| |||
Paste | |||
Oxygen sensor upstream of catalytic converter (G3/2) | |||
5 | Unclip and disconnect electrical connection for oxygen sensor upstream of CAT (G3/2x1) on bracket | Engine 271.9: Unclip electrical line from bracket (2). | |
6 | Unclip electrical line for oxygen sensor upstream of CAT (G3/2) on heat shield for the right engine mount | ||
7 | Remove oxygen sensor upstream of CAT (G3/2) from CAT (4) | The oxygen sensor upstream of CAT (G3/2) is a wideband sensor and therefore is extremely sensitive to the effect of applied forces. Pay attention to the following points otherwise the oxygen sensor upstream of CAT (G3/2) will be damaged: Engine 271.9: Do not pull out oxygen sensor upstream of CAT (G3/2) using pliers: just place with an open end wrench on the hexagon. When cleaning the thread, do not use any force (e. g. with pliers or vise) on the stem of the oxygen sensor upstream of CAT (G3/2). | |
Engine 271.9: When replacing the oxygen sensor upstream of CAT (G3/2) the balance resistor (3) for the new oxygen sensor (G3/2) is already put on and must not be replaced (resistance depends on the sensor). | |||
Installation: Coat thread with paste. | |||
| |||
Engine 271.8 | |||
Paste | |||
8 | Install in the reverse order | ||
9 | Attach STAR DIAGNOSIS and perform default initialization of the ME-SFI [ME] control unit | After replacing the oxygen sensor upstream of CAT (G3/2) | |
A default initialization must be conducted using STAR DIAGNOSIS in the ME-SFI [ME] control unit under the menu item "Control unit adaptations" since the mixture adaptation of the ME-SFI [ME] control unit must be reset. | |||
Danger! | Risk of accident caused by vehicle starting off by itself when engine is running. Risk of injury caused by contusions and burns during starting procedure or when working near the engine as it is running | Secure vehicle to prevent it from moving by itself. | |
10 | Perform engine test run while checking the exhaust system for leaks |
O2 sensor
Box wrench bit
000 589 71 03 00
Repair materials
Number | Designation | Order number |
BR00.45-Z-1005-06A | Paste, hot lubrication 1 kg, DB supply specification 6879.20 | A 000 989 76 51 |