Remove/install timing case

AR01.60-W-8200A

12.4.10

ENGINES 904.904 in MODEL 670

ENGINES 904.908 /914 /923 /936 in MODELS 668, 670

ENGINES 904.9 in MODEL 374, 375, 673, 674, 676, 958, 970, 972, 975, 976

ENGINES 902.9 in MODEL 957 with CODE (MS8) Natural gas engine
without rear engine power take-off

ENGINES 906.9 in MODEL 374, 958, 970, 972, 974, 975, 976
without rear engine power take-off

ENGINES 906.9 in MODEL 374, 375, 950, 952, 953, 954, 957, 958
without rear engine power take-off

W01.60-1014-06

1 Screw

2 Timing case

3 Dowel pins

4 Oil pan gasket

5 Screw

6 Oil pan

7 Radial sealing ring

8 Flywheel

B15 Crankshaft position sensor (on model 374, 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976)

B73 Crankshaft position sensor (on model 668, 670)

M1 Starter

Modification notes

5.3.08

Work procedure revised.

 	Remove/install
1	Remove engine	Model 668, 670 except engine 904.904	AR01.10-D-2400D
		Model 374.4, 375.1, 673, 674, 676, 958.0, 970, 972, 975, 976	AR01.10-W-2400D
		Model 374.5, 375.3, 950, 952, 953, 954, 958.2	AR01.10-W-2400F
		Model series 957	AR01.10-W-2400C
		Model 670 with engine 904.904  No removal instructions have been created for this model.
2	Mount engine on engine assembly stand	 Use an angle bracket.
3	Remove starter (M1)		*BA15.30-N-1004-01B
4	Remove oil pan (6)	Model 668, 670	AR01.45-D-7500D
		Model 673, 674, 676	AR01.45-W-7500A
		Model 374, 375, 950, 952, 953, 954, 958, 970, 972, 974, 975, 976	AR01.45-W-7500C
		Model series 957	AR01.45-W-7500D
5.1	Remove flywheel (8)	Vehicles with manual transmission	AR03.30-W-8002A
5.2	Remove ring gear carrier	Vehicles with automatic transmission
6	Take off attached parts at timing case (2)
7	Remove bracket with electrical wiring harness from timing case (2)
8.1	Remove crankshaft position sensor (B15)	Model 374, 375, 673, 674, 676, 950, 952, 953, 954, 957, 958, 970, 972, 974, 975, 976
		 Installation: Push plug bushing and crankshaft position sensor (B15) up to the end stop.
8.2	Pull out crankshaft position sensor (B73)	Model 668, 670
		 Installation: Press in plug bushing and crankshaft position sensor (B73) all the way.
9	Remove radial sealing ring (7)	 Installation: Only install radial sealing ring (7) when the timing case (2) is mounted on the cylinder crankcase.	AR03.20-W-3063A
10	Remove timing case (2)	 Loosen the timing case (2), using a plastic mallet if necessary.
		 Installation: Check the timing case (2) for damage, and replace timing case (2) if necessary, transferring all detachable parts.
			*BA01.60-N-1001-01A
11	Clean sealing surfaces	 Installation: Coat with sealing compound.	*BR00.45-Z-1009-01A
12	Install in the reverse order

 Timing case

Number	Designation		Engines 900.9, 902.9, 904.9, 906.9


BA01.60-N-1001-01A	Bolt, timing case to crankcase	Nm	50

 Starter

Number	Designation		Engines 900.9, 902.9, 904.9, 906.9


BA15.30-N-1004-01B	Bolt connecting starter to timing case	Nm	50

Repair materials

Number	Designation	Order number
BR00.45-Z-1009-01A	Sealing compound Loctite 574, 50 ml	A 001 989 89 20 10

เอกสารที่อ้างถึง